Reset Water Filter Counter; Eco Mode; Self-Test; Setting The Brightness Of The Control Panel - Thermador T30IB905SP Manual De Uso

Ocultar thumbs Ver también para T30IB905SP:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

en-us Operating the appliance

Reset water filter counter

After replacing the water filter, you have to reset the
water filter counter.
Press " button to open the Settings menu.
1.
Use ) button to move to the menu item Reset
2.
water filter counter.
Use 8 button to confirm, and confirm the query
3.
again with 8 button.
Note: If you cancel the query or take longer than
10 seconds to make an input, the water filter counter
will not be reset.
Switching the water filter counter on and off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
Press " button to open the Settings menu.
1.
Use ( button to move to the Appliance settings
2.
menu.
Press 8 button.
3.
Press ) button to move to the menu item Water
4.
filter counter.
To change the setting, press : button.
5.

Eco mode

Eco mode switches the appliance to energy-saving
operation.
The appliance automatically sets the following
temperatures:
Refrigerator compartment: +43 °F (6 °C)
Freezer compartment: +3 °F (–16 °C)
Switching Eco mode on or off
Press " button to open the Settings menu.
1.
Press ) button to move to the menu item Eco
2.
mode.
Press </= button.
3.
The temperature is changed and the display shows
the new temperature. When Eco mode is switched
off, the recommended temperature is set.
Note: You can also switch Eco mode on or off by
adjusting the temperature with -/+ buttons.

Self-test

This function can be used to start fault analysis on
your appliance.
~ "Appliance self-test" on page 31

Setting the brightness of the control panel

Press " button to open the Settings menu.
1.
Use ( button to move to the menu item Appliance
2.
settings.
16
Press 8 button.
3.
Press : button to open the menu
4.
item Brightness.
Press ( ) buttons to set the required brightness.
5.
Press 8 button.
6.
The setting is saved.
Press ; button to exit the menu.
7.

Switching key press sound on or off

You can switch the sounds generated when pressing
keys off and back on again.
Press " button to open the Settings menu.
1.
Use ( button to move to the menu item Appliance
2.
settings.
Press 8 button to open the menu item.
3.
Press ) button to move to the menu item Key
4.
press sound.
Press : button to open the menu item.
5.
Use ( ) buttons to select the required setting.
6.
Press 8 button.
7.
The setting is saved.
Press ; button to exit the menu.
8.

Setting the key volume

You can adjust the volume level of the sounds
generated when pressing keys.
Press " button to open the Settings menu.
1.
Use ( button to move to the menu item Appliance
2.
settings.
Press 8 button to open the menu item.
3.
Use ) button to move to the menu item Key
4.
volume.
Press : button to open the menu item.
5.
Use ( ) buttons to select the required setting.
6.
Press 8 button.
7.
The setting is saved.
Press ; button to exit the menu.
8.

Setting the signal tone volume

You can adjust the volume level of the signal tones
generated e.g. with alarms.
Press " button to open the Settings menu.
1.
Use ( button to move to the menu item Appliance
2.
settings.
Press 8 button to open the menu item.
3.
Use ) button to move to the menu item Signal
4.
tone volume.
Press : button to open the menu item.
5.
Use ( ) buttons to select the required setting.
6.
Press 8 button.
7.
The setting is saved.
Press ; button to exit the menu.
8.

Publicidad

Tabla de contenido
loading

Tabla de contenido