Audio Settings - Pioneer DEH-X8800BHS Manual De Instrucciones

Menu Item
PARENTAL CTRL
[LOCKED CH], [CLEAR ALL], [EDIT
CODE]

AUDIO settings

Menu Item
EQ SETTING
[SUPER BASS], [POWERFUL],
[NATURAL], [VOCAL], [CUSTOM1],
[CUSTOM2], [FLAT]
Select an equalizer band and
level for further customizing.
Equalizer band: [50HZ] to
[12.5kHZ]
Equalizer level: [–6] to [+6]
FADER*1 (Only for standard mode)
BALANCE
Description
Input the current passcode on the [PASSCODE]
screen (the default passcode is 0000).
1 Turn the M.C. dial to select a number.
2 Press the M.C. dial to move the cursor to the
next position.
3 After inputting the passcode, press the M.C.
dial.
4 Turn the M.C. dial to select one of the
following menu items, then press to confirm.
• [LOCKED CH]: Lock the current channel, which
contains mature content.
1 Press the M.C. dial to turn the lock on or off.
• [CLEAR ALL]: Unlock all the channels that have
restricted access.
1 Turn the M.C. dial to switch to [YES], then
press to confirm.
• [EDIT CODE]: Change the passcode.
1 Repeat steps 1 to 3 to enter a new passcode.
2 After inputting the passcode, press the M.C.
dial.
The new passcode is saved.
Description
Select or customize the equalizer curve.
• When you select a setting other than
[CUSTOM1] and [CUSTOM2], you can also
customize the equalizer curve by pressing and
holding the M.C. dial, then store the
customized equalizer curve in [CUSTOM1].
Adjust the front and rear speaker balance.
Adjust the left and right speaker balance.
Menu Item
SUBWOOFER
[ON], [OFF]
SUBWOOFER*2
[NOR], [REV]
SPEAKER LEVEL
Network mode: [HIGH L], [HIGH
R], [MID L], [MID R], [SUBWOOFER]
Standard mode: [FRONT L],
[FRONT R], [REAR L], [REAR R],
[SUBWOOFER]
Output level: [–24] to [10]
CROSSOVER
POSITION
[OFF], [FRONT LEFT] (front seat
left), [FRONT RIGHT] (front seat
right), [FRONT] (front seats), [ALL]*
* Only for standard mode
TIME ALGNMNT
[INITIAL], [ATA], [OFF], [CUSTOM]
Select a type of speaker and
adjust the speaker distance for
further customizing in [CUSTOM].
Network mode: [HIGH L], [HIGH
R], [MID L], [MID R], [SUBWOOFER]
Standard mode: [FRONT L],
[FRONT R], [REAR L], [REAR R],
[SUBWOOFER]
Speaker distance (inch): [140] to
[0]
Description
Set to [ON] when using a subwoofer speaker.
Select the subwoofer phase.
Select a speaker unit (filter) and adjust the
output level.
• Each value you have adjusted changes when
you change the [POSITION] setting (page 21).
Select a speaker unit (filter) to adjust the HPF or
LPF cut-off frequency and the slope for each
speaker unit.
For details on the [CROSSOVER] setting, see
page 17.
Select a listening position to adjust the speakers'
output levels automatically and add a delay time
that corresponds to the number and locations of
occupied seats.
Select or customize the time alignment settings
to reflect the distance between the listener's
position and each speaker.
• Select [INITIAL] to initialize the setting value.
• Select [ATA] to reflect the results of [AUTO TA &
EQ] in the setting value. [ATA] can only be
selected, if auto TA and EQ has already been
performed (page 18).
• Select [OFF] to reset all setting values to 0.
• The [CUSTOM] setting is available when
[FRONT LEFT] or [FRONT RIGHT] is selected in
[POSITION] (page 21).
• The [CUSTOM] setting is not available when
[OFF] is selected in [SUBWOOFER] (page 21).
21
En