Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

CHIMNEY
RANGE HOOD
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSON(S) OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock service disconnecting means to prevent
power from being switch on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer's guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local
code authorities.
5. This product may have sharp edges. Be carefule to avoid
cuts and abrasions during installation or cleaning.
6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. Do not use this unit with any other solid-state speed control
device.
9. Use only metal ductwork.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
cooking flaming foods (i.e. Crêpes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filters.
d) Use proper pan size. Always use cookware appropriate for
the size of the surface element.
INSTALLER: LEAVE THIS GUIDE WITH THE HOMEOWNER.
HOMEOWNER: OPERATION AND MAINTENANCE INFORMATION ON PAGE 2.
MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •
BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS
!
INTENDED FOR DOMESTIC COOKING ONLY
To register this product visit:
www.broan.com or
www.broan.ca
WARNING
TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN – You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels –
This could cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
know how to operate it.
B. The fire is small and contained in the area where it
started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or
unbalanced impeller, keep drywall spray, construction dust,
etc. off power unit.
4. Do not use over cooking equipment greater than 60,000
BTU/hr. as the blower motor will shut down intermittently.
5. Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes overheated.
The motor will restart when it cools down. If the motor
continues to shut off and restart, have the hood serviced.
6. The bottom of the hood MUST NOT BE LESS than 24" and
at a maximum of 36" above cooktop for best capture of
cooking impurities.
7. Two installers are recommended because of the size of
this hood.
8. To reduce risk of fire and to properly exhaust air, be sure
to duct air outside. Do not exhaust air into spaces within
walls or ceilings or into attics, crawl spaces, or garages.
9. Be careful when installing the decorative flue and hood,
they may have sharp edges.
10. Please read specification label on product for further
information and requirements.
!
.
!
Page 1

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Broan BWP1244SS

  • Página 1 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 1 CHIMNEY To register this product visit: www.broan.com or www.broan.ca RANGE HOOD READ AND SAVE THESE INSTRUCTIONS INTENDED FOR DOMESTIC COOKING ONLY WARNING...
  • Página 2: Cleaning & Maintenance

    MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 2 OPERATION CLEANING & MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. MOTOR The motor is permanently lubricated and never needs oiling. If...
  • Página 3: Prepare The Hood

    MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 3 INSTALL THE DUCTWORK PREPARE THE HOOD (Ducted Hoods Only) Unpack hood and check contents. You should receive: 1. Decide where ROOF CAP...
  • Página 4 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 4 PREPARE THE HOOD ( ’ INSTALL THE WIRING CONT For ducted installation only: Install both damper flaps inside the blower exhaust opening, LOCATE ensuring the pins are top oriented.
  • Página 5 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 5 INSTALL THE HOOD MOUNTING BRACKET WALL STUDS FRAMING BEHIND DRYWALL ⁄ ” ⁄ ” ⁄ ” NOTE: MOUNTING BRACKET LOCATION On 8-ft. ceilings (ABOVE 36”...
  • Página 6: Install Upper Flue Mounting Bracket

    MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 6 INSTALL UPPER FLUE MOUNTING INSTALL THE HOOD (Horizontally Ducted Hoods Only) BRACKET 1. DO NOT REMOVE the protective plastic film covering the...
  • Página 7 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 7 UPPER FLUE MOUNTING BRACKET 6” ROUND DUCT ELBOW UPPER FLUE 9. Measure and install 6” round steel ductwork to roof cap or...
  • Página 8 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 8 UPPER FLUE MOUNTING BRACKET 6” ROUND STEEL DUCT UPPER DUCT LENGTH FLUE DECORATIVE FLUE 7. Measure and install 6” round steel ductwork to the blower exhaust opening on top of hood.
  • Página 9 MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 9 4. Remove the 12. Hold hood up close to wall mounting location and plug grease filters power cord into wall outlet. by pulling 13.
  • Página 10: Service Parts

    MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 10 SERVICE PARTS BWP1 Series KEY PART NO. DESCRIPTION QTY. 1 S99526972 Decorative Upper and Lower Flues 2 S99010499 Damper Flap 3 S99010484 Control Assembly...
  • Página 11 Limited Warranty Warranty Period and Exclusions: Broan-NuTone LLC and Venmar Ventilation ULC (either being the “Company”) warrants to the original consumer purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period of one (1) year from the date of original purchase (or such longer period as may be required by applicable law).
  • Página 12 MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 12 HOTTE Pour enregistrer ce produit, visitez : www.broan.com ou CHEMINÉE www.broan.ca LIRE CES DIRECTIVES ET LES CONSERVER POUR USAGE DOMESTIQUE SEULEMENT AVERTISSEMENT AVERTISSEMENT AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGES...
  • Página 13: Nettoyage Et Entretien

    MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 13 FONCTIONNEMENT NETTOYAGE ET ENTRETIEN Un entretien adéquat de la hotte assurera son bon fonctionnement. MOTEUR Le moteur est lubrifié en permanence et n’a pas besoin d’être HC0095 huilé.
  • Página 14: Préparation De La Hotte

    MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 14 POSE DU CONDUIT PRÉPARATION DE LA HOTTE (Hottes avec conduit seulement) Déballer la hotte et vérifier le contenu de la boîte. Celle-ci doit 1.
  • Página 15: Installation Du Câblage

    MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 15 PRÉPARATION INSTALLATION DU CÂBLAGE DE LA HOTTE ( SUITE Pour les installations avec conduit seulement : Installer les deux clapets à l’intérieur de l’ouverture d’évacuation du ventilateur, en s’assurant que les tiges sont sur le dessus.
  • Página 16: Installation Du Support De Montage De La Hotte

    MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 16 INSTALLATION DU SUPPORT DE MONTAGE DE LA HOTTE MONTANTS CHARPENTE DERRIÈRE LA CLOISON SÈCHE ⁄ ⁄ ⁄ EMPLACEMENT DU SUPPORT DE MONTAGE (AU-DESSUS D’UNE SURFACE DE CUISSON DE 36 PO...
  • Página 17: Installation De La Hotte

    MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 17 INSTALLATION DU SUPPORT DE MONTAGE DE CONDUIT INSTALLATION DE LA HOTTE DÉCORATIF SUPÉRIEUR (évacuation horizontale seulement) 1. NE PAS enlever à cette étape la pellicule protectrice en Plafond Centre de l’installation...
  • Página 18 MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 18 SUPPORT DE MONTAGE DU CONDUIT DÉCORATIF SUPÉRIEUR COUDE ROND DE 6 po CONDUIT DÉCORATIF SUPÉRIEUR 9. Mesurer et installer un conduit rond de 6 po jusqu’au capuchon de toit ou capuchon mural et un coude de 90°...
  • Página 19 MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 19 SUPPORT DE MONTAGE DE CONDUIT ROND CONDUIT DÉCORATIF SUPÉRIEUR EN ACIER DE 6 PO CONDUIT LONGUEUR DU CONDUIT DÉCORATIF SUPÉRIEUR CONDUIT DÉCORATIF 7.
  • Página 20 MODÈLES BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Page 20 4. Enlever les 12. Soulever et maintenir la hotte près de son emplacement et filtres à brancher son cordon électrique dans la prise.
  • Página 21: Pièces De Rechange

    S99010486 Filtres à chicane hybrides (paire) (BWP2244SS) toujours utiliser des pièces d’origine provenant de Broan-NuTone LLC ou de Venmar Ventilation ULC. Les pièces d’origine de Broan- S99010487 Filtres à chicane hybrides (paire) NuTone LLC et de Venmar Ventilation ULC sont spécialement (BWP2304SS, BWP2306SS) conçues pour satisfaire toutes les normes de certification de sécurité...
  • Página 22 Garantie limitée Période de garantie et exclusions : Broan NuTone LLC (la « Société ») ou Venmar Ventilation ULC et/ou son subsidiaire garantit au consommateur acheteur initial (« vous ») de son produit (le « Produit ») que celui-ci est exempt de tout vice de matériau ou de fabrication pour une période de un (1) an à...
  • Página 23 MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 23 Para registrar este producto CAMPANA DE visite: www.broan.com o www.broan.ca ESTUFA DE CHIMENEA LEA Y CONSERVE ESTAS INSTRUCCIONES INDICADA SOLAMENTE PARA COCINAR EN CASA...
  • Página 24: Funcionamiento

    MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 24 FUNCIONAMIENTO LIMPIEZA Y MANTENIMIENTO El mantenimiento correcto de la campana de la estufa asegurará el funcionamiento adecuado de la unidad. MOTOR El motor está permanentemente lubricado y nunca necesitará...
  • Página 25: Instale Los Conductos

    MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 25 INSTALE LOS CONDUCTOS PREPARE LA CAMPANA (sólo en campanas con conductos) 1. Decida dónde Desempaque la campana y revise el contenido del paquete.
  • Página 26: Instale El Cableado

    MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 26 PREPARE LA INSTALE EL CABLEADO CAMPANA ( CONTINUACIÓN Para las instalaciones con conducto solamente: ENCUENTRE EL TOMACORRIENTE Instalar ambas clapetas al interior de la abertura de descarga 4 PULG.
  • Página 27: Instale El Soporte De Montaje De La Campana

    MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 27 INSTALE EL SOPORTE DE MONTAJE DE LA CAMPANA MONTANTES DE PARED MARCO DETRÁS DE LA PLACA DE YESO pulg. ⁄ pulg. ⁄...
  • Página 28: Instalación Del Soporte De Montaje Del Tubo De Humos Superior

    MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 28 INSTALACIÓN DEL SOPORTE DE MONTAJE DEL TUBO DE HUMOS INSTALACIÓN DE LA CAMPANA SUPERIOR (Sólo con conductos horizontales) 1. En este momento NO QUITE la película de plástico protector Cielo raso Centro de la instalación...
  • Página 29 MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 29 SOPORTE DE MONTAJE DEL TUBO DE HUMOS SUPERIOR CODO DE CONDUCTO TUBO DE REDONDO DE HUMOS 6 PULG. SUPERIOR 9. Mida e instale los conductos redondos de acero de 6 pulg.
  • Página 30 MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 30 SOPORTE DE MONTAJE DEL TUBO DE HUMOS SUPERIOR CONDUCTO REDONDO DE ACERO TUBO DE DE 6 PULG. HUMOS LONGITUD DEL SUPERIOR CONDUCTO...
  • Página 31 MODELOS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS Página 31 4. Retire los 12. Sostenga la campana cerca de la ubicación de montaje en filtros de grasa la pared y conecte el cordón eléctrico en el tomacorriente.
  • Página 32: Piezas De Servicio

    (BWP2364SS, BWP2366SS) nivel de rendimiento, lo cual podría causar una falla prematura. Broan-NuTone LLC y Venmar Ventilation ULC recomiendan comunicar con un centro de S99528929 Soportes de montaje (juego de 3) servicios autorizado para todos los repuestos y reparaciones.
  • Página 33: Garantía

    Garantía limitada Periodo y exclusiones de la garantía: Broan-NuTone LLC o Venmar Ventilation ULC (sea esta la “Compañía”) garantiza al consumidor comprador original de su producto (“usted”) que el producto (el “Producto”) estará libre de defectos en materiales o en mano de obra, por un periodo de un (1) año a partir de la fecha de compra original (o por un periodo mayor según sea requerido por la legislación aplicable).

Tabla de contenido