Tabla de contenido
Publicidad
Heben der Last
Schalthebel in Richtung Heben ‚ ' stellen und
einrasten lassen (Fig. 10).
Mit Handhebel Pumpbewegungen ausführen.
Wenn das Hebezeug unter Last steht, ohne
dass damit gearbeitet wird, muss der Schalt-
hebel in Stellung Heben ‚ ' verbleiben.
Die Last stets in der Hakenmitte einhängen.
Hakenspitze nicht belasten (Fig. 8).
Senken der Last
Schalthebel in Richtung Senken ‚ ' stellen und
einrasten lassen (Fig. 10).
Mit Handhebel Pumpbewegungen ausführen.
Verspannung der Bremse
Wird ein unter Last stehendes Hebezeug durch
Abheben der Last bzw. Einreißarbeiten plötz-
lich entlastet, ohne das zuvor die Senkarbeit
eingeleitet wurde, so bleibt die Bremse ge-
schlossen. Ein Schließen der Bremse erfolgt
ebenfalls, wenn der Lasthaken mit der Unter-
flasche zu fest gegen das Gehäuse gezogen
wird.
Lösen der verspannten Bremse
Schalthebel in Richtung Senken , ' stellen und
Handhebel ruckartig durchdrücken. Falls die
Verspannung sehr hoch ist, kann die Bremse
mit einer schlagartigen Belastung auf den
Handhebel gelöst werden.
PRÜFUNG / WARTUNG
Die Prüfung ist mindestens einmal jährlich,
bei schweren Einsatzbedingungen in kürzeren
Abständen, durch einen Sachkundigen
vorzunehmen. Die Prüfungen sind im
Wesentlichen Sicht- und Funktionsprüfungen,
wobei der Zustand von Bauteilen hinsichtlich
Beschädigung, Verschleiß, Korrosion oder
sonstigen Veränderungen beurteilt sowie die
Vollständigkeit und Wirksamkeit der
Sicherheitseinrichtungen festgestellt werden
muss.
Die Prüfungen sind vom Betreiber zu
veranlassen.
English
GB
INTRODUCTION
All users must read these operating instruc-
tions carefully prior to the initial operation.
These instructions are intended to acquaint
the user with the hoist and enable him to use
it to the full extent of its intended capabilities.
The operating instructions contain important
information on how to handle the hoist in a
safe, correct and economic way. Acting in ac-
cordance with these instructions helps to avoid
dangers, reduce repair cost and down time
and to increase the reliability and lifetime of
the hoist. Apart from the operating instructions
and the accident prevention act valid for the
respective country and area where the hoist
is used, also the commonly accepted regula-
tions for safe and professional work must be
adhered to.
CORRECT OPERATION
- The unit is used for lifting, pulling and ten-
sioning of loads.
- The unit can also be used for lashing of loads
on trucks etc. please refer to the values for
hand and tensioning force "S" mentioned
on the name plate.
- The capacity indicated on the product is the
maximum safe working load (W.L.L.) that
may be lifted.
- Do not allow personnel to pass under a sus-
pended load.
- After lifting or tensioning, a load must not
be left unattended for a longer period of time.
- Start moving the load only after it has been
attached correctly and all personnel are clear
of the danger zone.
- The operator must ensure that the load is
attached in a manner that does not expose
himself or other personnel to danger by the
hoist, chain(s) or the load.
- The hoists can be operated in ambient tem-
peratures between -10°C and +50°C.
Consult the manufacturer in case of extreme
working conditions.
Note: At ambient temperatures below 0°C
the brake should be checked for freezing.
- The accident prevention act and/or safety
regulations of the respective country for us-
ing manual hoists must be strictly adhered
to.
- In order to ensure correct operation, not only
the operation instructions, but also the con-
ditions for inspection and maintenance must
be complied with.
- lf defects are found stop using the hoist im-
mediately.
INCORRECT OPERATION
- Do not exceed the rated capacity of the hoist.
- It is forbidden to use this product for the
transportation of people (Fig. 1).
- Do not extend the hand lever (Fig. 2).
- Welding on hook and load chain is strictly for-
bidden. The load chain must never be used
as ground connection during welding (Fig. 3).
- Avoid side pull, i. e. side load on either hous-
ing or bottom block (Fig. 4).
- The load chain must not be used for lashing
purposes (sling chain) (Fig. 5).
- Do not knot or shorten the load chain by
using bolts/screws/screwdrivers or other
devices (Fig. 6). Do not repair load chains
installed in the hoist.
- Do not remove the safety latch from the top
or bottom hooks (Fig. 7).
- Never attach the load on the tip of the hook.
This also applies to the top hook (Fig. 8).
- Do not use the chain stop as an operational
limit device (Fig. 10).
- Do not throw the hoist down. Always place it
properly on the ground.
INSPECTION PRIOR TO INITIAL
OPERATION
Each unit must be inspected prior to initial
operation by a competent person. The inspec-
tion is visual and functional. This inspection
shall establish that the unit is safe and has
not been damaged by incorrect transport or
storage. Inspections should be made by a re-
presentative of the manufacturer or the supp-
lier although the company can assign its own
suitably trained personnel.
INSPECTION BEFORE STARTING WORK
Before starting work inspect the hoist, chain(s)
and all load bearing constructions every time
for visual defects. Furthermore test the brake
and make sure that the load and hoist are
correctly attached. For this purpose a short
work cycle of lifting/pulling or tensioning and
releasing should be carried out.
Load chain inspection
Inspect the load chain for sufficient lubrica-
tion and visually check for extemal defects,
deformations, superficial cracks, wear or cor-
rosion marks.
Chain stop inspection
The chain stop must be connected to the free
(idle) chain strand (Fig. 10).
Inspection of top and bottom hooks
Inspect top and bottom hooks for deforma-
tions, damage, cracks, wear or corrosion
marks.
3
Publicidad
Tabla de contenido
