Hoshizaki KM-40B Manual De Instrucciones página 4

Máquina autocontenida de cubitos en forma de media luna
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
I. INSTALLATION INSTRUCTIONS
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging elements
(plastic bags and expanded polystyrene) as they are potential
sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing material
is left in the icemaker, it will not work properly.
Top Panel
Separator
Door
Accessories
(inside bin)
Control Switch
Air Filter
1) After removing the packaging, make sure that the icemaker is in good
condition. If in doubt, please do not use the equipment but apply to
professionally qualified personnel.
2) Remove shipping tape holding the door and separator.
3) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Outlet Hose
b) Scoop
c) Adjust Bolt
d) Power Supply Cord (European model)
2. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor use. Normal operating
ambient temperature should be within 7°C to 40°C. Normal
operating water temperature should be within 7°C to 35°C.
Operation of the icemaker, for extended periods, outside
of these normal temperature ranges may affect production
capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for the
equipment.
4. Allow 15 cm clearance at rear and sides for proper air circulation
and ease of maintenance and/or service should they be
required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
Icemaking
Mechanism
Control Box
Refrigeration
Circuit
Louver
Fig. 1
1
1
4
1
6. Do not place anything on top of the icemaker or in front of the
louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").
3. INSTALLATION
* Incorrect installation can cause harm to people, animals or things, for
which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is accessible.
4. ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local
electrical code requirements. To prevent possible severe electrical
shock to individuals or extensive damage to equipment, install a
proper earth wire to the icemaker. Remove the plug from the mains
1:2
socket before any maintenance, repairs or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
* The main control box fuse is rated at 5A and should only be replaced
1:2
by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician are
required.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol
or coloured Green or Green-and-Yellow. The wire which
is coloured Blue must be connected to the terminal which is marked
with the letter N or coloured Black. The wire which is coloured Brown
must be connected to the terminal which is marked with the letter L
or coloured Red.
* Should the socket outlets in the installation site not be suitable for the
plug supplied with your product, the plug must be removed (cut off if
it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord, it
must be disposed of. There should be no attempt to reuse it. Inserting
such a plug into a socket elsewhere presents a serious risk of electrical
shock.
* The non-rewirable plug must never be used without a fuse cover being
fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 10A and approved to BS 1362.
3
ENGLISH
WARNING

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Km-55bKm-80b

Tabla de contenido