Tabla de contenido
Publicidad
SM 2610008289 02-10:3310 Table Saw 2/2/10 8:39 AM Page 68
Dado and Molding Cutting
Instructions for operating the saw with Dado and Molding Head
sets are contained in the booklet furnished with these accessories.
ALWAYS USE AN APPROPRIATE SKIL TABLE INSERT AND
WASHERS LISTED UNDER RECOMMENDED ACCESSORIES.
ALWAYS PLACE THE BLADE WASHERS IN THE ORIGINAL
POSITIONS WHEN YOU ARE FINISHED DADO OR MOLDING
CUTTING.
INSTALLING A DADO SET
A dado set is an accessory system used to make non-thru grooves
or lap cuts on work pieces. These tools are commonly used in
furniture and cabinet building. After work pieces have been
properly dado cut, they can be tightly joined together. The 3310
table saw can accommodate dado cutting up to 1/2" wide in a
single pass.
To reduce the risk of injury, always
W RNING
disconnect plug from power source before
changing blades.
To reduce the risk of injury, always use the
W RNING
Skil Dado Blade Table Insert No. 2610011336
(comes with a dado accessory washer). Never make dado cuts
without this insert. Do not use dado sets larger than 8" diameter.
Never set dado cutters to any bevel angle other than the vertical 0°
angle. Follow all warnings and instructions shown here and those
that accompany your dado set. Failure to comply with these
warnings may result in serious bodily injuries.
To reduce the risk of injury, do not use dado
W RNING
sets larger than 8 inches in diameter. The saw
is not designed to accept larger sized dados.
FIG. 51
RBOR
RBRE
EJE PORT HERR MIENT
INNER BL DE W SHER
RONDELLE DE L ME
INTÉRIEURE
R NDEL INTERIOR DE
L HOJ
CHIPPERS
L MES DÉCHIQUETEUSES
INNER BL DE
STILL DORES
L ME INTÉRIEURE
HOJ INTERIOR
68
USING STACKED DADO SETS
1. Disconnect plug from power source.
2. Remove the Smart Guard System and Anti-Kickback Device
(see page 40, 42). Lower and lock the Riving Knife in its lowest
position.
3. Remove standard table insert plate. Raise saw blade to
maximum height.
4. Remove the arbor nut, outer washer, and saw blade.
5. Installing a dado stack (Fig. 51)
A) Place the desired parts of the dado set onto the arbor shaft.
B) Place the outer washer onto the outside of the dado stack.
C) Replace and tighten the arbor nut onto the arbor shaft.
6. Placing dado blades and chippers: (see Fig. 51)
• For 1/4" wide cuts, place the two outside dado blades (cutters)
on the shaft. The two dado outside blades may be different,
check for information on the blade and the manufacturer's
instructions for proper installation.
• For wider cuts (up to 1/2" maximum), chipper blades and
spacers can be placed only between the outside blades
(cutters).
RONDELLE DE L ME EXTÉRIEURE
R NDEL EXTERIOR DE L HOJ
OUTER BL DE
L ME EXTÉRIEURE
HOJ EXTERIOR
OUTER BL DE W SHER
(5/16" OR LESS)
(5/16 PO OU MOINS)
(5/16 PULG D O MENOS)
RBOR NUT
ÉCROU DE FIX TION DE L' RBRE
TUERC DEL EJE
PORT HERR MIENT
CCESSORY D DO W SHER
(5/16" TO 1/2" M X.)
RONDELLE CCESSOIRE POUR L ME À
R INURER
(5/16 PO M X. 1/2 PO)
R NDEL
CCESORI P R
MORT J R
(5/16
MÁX. 1/2 PULG D )
Publicidad
Tabla de contenido
