EGO ST1500E Manual Del Usuario página 11

NOTICE:
The trimmer head is parallel to the ground at
a proper cutting distance without operator bending over
(Fig. P).
Adjust the shoulder strap in a comfortable operating po-
sition. Hold the string trimmer with both hands: One hand
on the rear handle and the other hand on the front-assist
handle.
STARTING/STOPPING THE STRING TRIMMER (Fig. Q)
To Start
Press down the lock-off lever then depress the trigger.
Different pressure on the trigger results in variable rotating
speed of the cutting line. More pressure, higher speed.
To Stop
Release the lock-off lever and the trigger.
NOTICE: The motor runs only when the lock-off lever and
trigger are both pressed.
WARNING: Always remove the battery pack from
the string trimmer during work breaks and after finishing
work.
USING THE STRING TRIMMER
WARNING: To avoid serious personal injury, wear
goggles or safety glasses at all times when operating this
unit. Wear a face mask or dust mask in dusty locations.
Clear the area to be cut before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or line,
that can be thrown or become entangled in the cutting
attachment. Clear the area of children, bystanders, and
pets. At a minimum, keep all children, bystanders and pets
at least 15m away; there still may be risk to bystanders
from thrown objects. Bystanders should be encouraged to
wear eye protection. If you are approached, stop the motor
and cutting attachment immediately.
Before each use, check for damage/worn parts
Check the bump head, guard and front-assist handle
and replace the parts that are cracked, warped, bent, or
damaged in any away.
The line-cutting blade on the edge of the guard can dull
over time. It is recommended that you periodically sharpen
it with a file or replace it with a new blade.
WARNING: Always wear gloves when mounting the
guard or sharpen or replacing the blade. Take care of the
blade on the guard and protect your hand from cutting.
After each use, clean the trimmer.
CAUTION:
the air from flowing into the motor housing and result in
overheating or damaged of the motor.
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Keep air vents in the motor housing from debris at all
times.
WARNING:
trimmer. Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to damage from
various types of commercial solvents. Use clean cloths to
remove dirt, dust, oil, grease, etc.
ADJUSTING CUTTING LINE LENGTH
The bump head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the bump knob on the ground while operating the
trimmer (Fig. R).
NOTICE:
cutting line becomes shorter.
WARNING:
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
LINE REPLACEMENT
NOTICE:
diameter no more than Ø 2.4 mm.
WARNING:
rope, etc. These can break off and become dangerous
projectiles.
There are two methods to replace the cutting line:
1. Wind the spool with new line.
2. Install a pre-wound spool (AS1300, if necessary,
available in dealer).
Wind the spool with new line
Press the two release tabs on the spool base and pull
the spool retainer out (Fig. S). Take approximately 5m
of 2.4mm diameter cutting line. Fold and wind it onto
the spool as Fig. T & U shown. Then place the line ends
through the two opposite notches in the spool (Fig. V) and
place the spool into its retainer with notches aligned with
retainer eyelets (Fig. X). Lastly, align the retainer slots with
the tabs on the spool base and press the retainer evenly
down, ensuring that it snaps into place (Fig. W).
56 VOLT LITHIUM-ION CORDLESS STRING TRIMMER — ST1500E
Obstructions in the vents will prevent
Never use water for cleaning your
Line release will become more difficult as the
Do not remove or alter the line cutting
Always use standard nylon cutting line with
Never use metal-reinforced line, wire,
EN
11