Specific Safety Instructions - stayer TH610 Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com
The drill is designed for drilling holes into wood, iron, non-
ferrous metals and rock using the appropriate bits.

Specific safety instructions

Wear hearing protection. Exposure to noise can cause
hearing loss.
Always use the auxiliary handle supplied with the
machine. Loss of control can cause personal injury.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to
fire and electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes property
damage or may cause an electric shock.
Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal
parts of the power tool "live" and shock the operator.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Do not work materials containing asbestos. Asbestos
is considered carcinogenic.
Take protective measures when dust can develop
during working that is harmful to one's health,
combustible or explosive.
Example: Some dusts are regarded as carcinogenic.
Wear a dust mask and work with dust/chip extraction
when connectable.
Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
"Caution - Read the operating instructions to re-
duce the risk of inquiry"
ENGLISH
13
Wear ear-muffs. The impact of noise can cause
damage to hearing.
Wear a breathing mask.
Dust which is injurious to health can be genera-
ted when working on wood and other materials.
Never use the device to work on any materials
containing asbestos!
Wear safety goggles.
Sparks generated during working or splinters,
chips and dust emitted by the device can cause
loss of sight.
Instructions for use
Placement Tool
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be liable
for any damage or injuries of any kind caused as a result
of this.
Assembly
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical to
the mains data.
Before any work on the machine itself, pull the
mains plug.
Fitting the additional handle (Fig. 2-3/Item 7)
The additional handle 7 enables you to achieve better
stability whilst using the hammer drill. Do not use the tool
without the additional handle.
The additional handle 7 is secured to the hammer drill by
a clamp. During the handle clockwise tightens this clamp.
Turning it anti-clockwise will release the clamp.
The supplied additional handle 7 must first be fitted. To do
this, the clamp must be opened by turning the handle until
it is wide enough for the additional handle to be slid over
the chuck 1 and on to the hammer drill.
After you have positioned the additional handle 7, turn it to
the most comfortable working position for you.
Now turn the handle in the opposite direction again until
the additional handle is secure.
The additional handle 7 is suitable for both lefthanded and
right-handed users.
Fitting and adjusting the depth stop (Fig. 4/Item 2)
The depth stop 2 is held in place by the additional handle
7 by clamping. The clamp can be released and tightened
by turning the handle. Release the clamp and fit the depth
stop 2 in the recess provided for it in the additional handle.
13