Doctor's Function - Beurer EM 49 Instrucciones De Uso

Ocultar thumbs Ver también para EM 49:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 57
working time and pause time for this program to between 1 and 30
seconds each.
1. Place the electrodes on the desired area for treatment (for
positioning suggestions see electrode positions in section 6.4)
and connect them to the device.
2. Select the EMS 34 program as described in section "5.2 Starting
application" (step 3 to step 5).
˄/˅
3. Use the
setting buttons to select the working time ("on
time") you want and use the ENTER button to confirm.
˄/˅
4. Use the
setting buttons to select the pause time ("off time")
you want and use the ENTER button to confirm.
˄/˅
5. Use the
setting buttons to select the impulse frequency you
want and use the ENTER button to confirm.
˄/˅
6. Use the
setting buttons to select the impulse width you want
and use the ENTER button to confirm.
˄/˅
7.Use the
setting buttons to select the treatment time you want
and use the ENTER button to confirm.
˄/˅
8.Use the left and right
select the impulse intensity you want.
EMS 35 program
EMS 35 is a burst program that you can also customise. Various
impulse sequences run in this program. Burst programs are suitable
for all areas of application to be treated with changing signal
patterns (to minimise the level of accustoming to the treatment).
In this program, you can set the impulse frequency to between 1
and 150 Hz and the impulse width to between 80 and 450 μs. You
can also set the working time and pause time for this program to
between 1 and 30 seconds each.
1. Place the electrodes on the desired area for treatment (for
positioning suggestions see electrode positions in section 6.4)
and connect them to the device.
2. Select the EMS 35 program as described in section "5.2 Starting
application" (step 3 to step 5).
setting buttons for
and
˄/˅
3. Use the
setting buttons to select the working time ("on
time") you want and use the ENTER button to confirm.
˄/˅
4. Use the
setting buttons to select the pause time ("off time")
you want and use the ENTER button to confirm.
˄/˅
5. Use the
setting buttons to select the impulse frequency you
want and use the ENTER button to confirm.
˄/˅
6. Use the
setting buttons to select the impulse width you want
and use the ENTER button to confirm.
˄/˅
7.Use the
setting buttons to select the treatment time you want
and use the ENTER button to confirm.
8.Use the left and right
select the impulse intensity you want.

8. Doctor's function

The Doctor's function is a special setting to allow you to access
your personal program even more easily and directly.
Your individual program settings are instantly recalled and activated
when the device is switched on.
to
You may wish to adjust this individual program following advice from
your doctor.
Setting the Doctor's function
• Select your program and the corresponding settings as described
in section "5.2 Starting application".
• At the start of the stimulation treatment, the impulse intensity of
and
is set to 00 by default. No impulses are sent to the
electrodes yet. Before setting the desired impulse intensity using
the intensity setting buttons, press and hold the
5 seconds. Storage in the Doctor's function is confirmed with a
long acoustic signal.
If you switch on the device again, the program you saved using
the Doctor's function is automatically opened directly.
Deleting the Doctor's function
To clear the device again and to re-allow access to other programs,
press and hold the
do this, the impulse intensity of
33
˄/˅
setting buttons for
˅
-button again for approx. 5 seconds. To
and
must be set to 00.
and
to
˅
-button for

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido