Overview Of The Components; Unpacking The Appliance; Installation And Use - Clatronic KM 3333 Instrucciones De Servicio

Кухонный комбайн CLATRONIC KM 3333
Купить в интернет-магазине http://clatronic-shop.com.ua

Overview of the Components

1 Filling slot seal
2 Mixer vessel lid with filling slot
3 Mixer vessel
4 Drive shaft for mixing bowl
5 Utensil switch
6 Kitchen machine, basis appliance
7 Filler
8 Lid of the mixing bowl with feed tube
9 Mixing bowl
10 Mixing bowl driveshaft
11 Potato rasp
12 Grating insert, fine
13 Cutting insert, fine
14 Grating insert, coarse
15 Cutting insert, coarse
16 French fries disk
17 Utensil holder
18 Dough hook
19 Chopping blade
20 Locating pin
21 Safety cover for mixer drive
22 Whisking and emulsifying disc
23 Dough scraper
The following remark is to be found on the lid (8):
"CAUTION:
DO NOT OPERATE WITHOUT THIS COVER IN PLACE"

Unpacking the appliance

• Remove the appliance from the box and all the enclosed
accessories.
• Before the device is used for the first time the mixing bowl,
processor bowl, various lids and other accessories should
be washed in soapy water to remove any contamination
from their production.
WARNING:
Some parts are extremely sharp! There is the risk of being
injured under certain circumstances!
• Clean each single part one after the other and with great
caution!
• Dry well all the parts after washing.

Installation and use

Make sure that the switch (5) is positioned on "0" and that the
appliance plug is not inserted when changing the attachments.
Only now can the attachments be mounted and used.
The safety cover (21) has to be mounted on the drive shaft of
the mixer drive (4) when you operate the grater bowl in order to
avoid any injuries.
The appliance cannot be used without the safety lid!
Even if you would only like to use the mixer, the mixing bowl
must be in place.
36
• Short-term operation: If the device is subjected to a full
load (e.g. cutting meat up into slices) it should not be opera-
ted for more than 40 seconds. Please allow it to cool down
for 10 minutes before using it again!
• Pulse operation: Pulse mode is turned on by turning the
switch to the "P" position and releasing it again. The device
should not be used in this mode for more than 1 minute.
Allow it to cool down for 2 minutes before using it again!
Electrical connection
Check whether the electrical voltage that you intend to use is
the same as that of the machine. Details are to be found on the
label on the base.
Operation
Assembly of mixing bowl and lid
Position the cover for the mixer drive (21) on the drive shaft
of the mixing vessel (4) such that the
pointing to the  arrow on the base of the device. Turn the
cover for the mixer drive in a clockwise direction as far as it will
go (Illustration 1).
1. Place the mixing bowl (9) on the base in such a way that the
 marking on the lower edge of the bowl is in line with the
 marking on the basis. Then turn the bowl clockwise until
you hear it lock into place (Illustration 2 + 3).  and  must
be completely in line with one another.
2. Place the locating pin (20) over the drive shaft of the mixing
bowl (10) (Fig. 4) and select the corresponding tool (see the
section on "Mixing Bowl Operation").
3. Position the lid (8) in such a way that the arrow  on the lid
is aligned with the right-hand mark
The metal tip of the locating pin (20) has to engage into its
bearing in the lid. If this is not the case, check that the loca-
ting pin is correctly in position. Turn the lid in the direction of
the closed lock until it is heard to lock in place (Fig. 6). To
remove the lid, turn it in an anticlockwise direction.
Positioning the Mixing Bowl and Lid (Illustration 13-15)
1. Hold the mixer vessel (3) in such a way that the handle is on
the left-hand side. Place the mixing bowl on the base of the
device in such a way that the  mark on the bottom edge
of the bowl points to the  arrow on the base of the device.
Turn the mixer vessel in the direction of the arrow until it is
heard to lock in place.  and  must be completely in line
with one another.
2. When replacing the lid (2), ensure that the spout opening on
the lid is above the spout of the mixer vessel.
3. Tighten the lid in a clockwise direction until it is heard to
lock in place.To remove the lid, turn it in an anticlockwise
direction.
Double Safety System
The motor can only be switched on if the grater bowl with the
cover locks into place correctly and the cover for the mixer drive
(21) is mounted. The mixer can only be used if the grater bowl is
correctly positioned. You should only remove the lid from the gra-
ter bowl or from the mixing vessel when the device is switched off.
mark on the cover is

on the grater bowl.