DeWalt DW754 Manual Del Usuario página 24

EngLIsh
5. Position the guard at a distance of approx. 2 mm from the
wheel by sliding it towards the wheel.
6. Securely tighten the nut (torque: 6 Nm).
Adjusting the workpiece support (Fig. G)
The workpiece support can be set according to the workpiece
and the desired grinding angle.
1. Slacken the nut holding the support
2. Set the support to the desired position and angle, making
sure that the support is as close to the wheel as possible.
3. Tighten the nut (torque: 6 Nm).
Mounting and adjusting the clamping and
grinding attachment (Fig. A, H)
The clamping and grinding attachment is used to hold the
workpiece to the grinding wheel at a fixed angle.
1. Remove the fasteners holding the workpiece support
the bracket 4 and remove the workpiece support (Fig. A).
2. Mount the grinding attachment bracket
4 on the machine as shown using the hexagonal head
bolt 23 and corresponding nut
the grinding attachment bracket is at a distance of approx.
2 mm from the grinding wheel.
3. Insert the rod 25 of the grinding attachment into the forks
on the grinding attachment bracket as shown.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. J)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Refer to Figure J for proper body stance and hand positioning
when grinding and honing.
Switching On and Off (Fig. A)
To turn the tool on, set the on/off switch
To turn the tool off, set the on/off switch
Using the Grinding Wheel (Fig. A)
In order to achieve a straight cutting edge, move it slowly
backwards and forwards over the grinding wheel
a light pressure.
22
.
3
3 to
22 to the bracket
24 (Fig. H). Make sure that
to position 1.
1
1 to position 0.
2 . Only exert
Using the Clamping and Grinding
Attachment (Fig. I)
1. Insert the workpiece into the clamping bracket
2. Position the workpiece as required to obtain the correct
bevel angle. The angle is a function of the protruding length
X (see Figure). For plane irons, X should be approx. 20 mm,
for chisels approx. 25–28 mm.
3. Tighten the star knobs
27
Using the Honing Wheel (Fig. A)
Move the workpiece slowly horizontally backwards and
forwards over the honing wheel
of the workpiece should be in contact with the wheel over a
width of 0.5 to 1 mm.

WARNING: Do not use any honing paste on the
honing wheel.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
On a weekly basis, remove grindings from the housing and
the covers.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Keep the ventilation slots clear and regularly clean the housing
with a soft cloth.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
26 .
.
. The tip of the cutting edge
5