Maintenance / Service - Skil 4381 Manual Original

• Selecting sawing mode !
- 'EXACT' for accurate cutting, straight + curved
- 'TURBO' for fast cutting, straight cuts only
! always select 'EXACT' when sawing splinter-
sensitive material
• Adjusting sawing speed to material used @
! if the tool does not run with wheel D in position 1,
select a higher sawing speed and lower the
sawing speed while the tool runs
• Dust suction #a
! do not use vacuum cleaner when cutting metal
• Dust blowing #b
• Operating the tool
- before switching on the tool, ensure that front end of
footplate rests flat on the workpiece
- hold tool firmly with both hands, so you will have full
control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) $
- ensure that complete surface of footplate rests firmly
on the workpiece
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
- keep ventilation slots F 2 uncovered
• Cable clip %
APPLICATION ADVICE
• Use the appropriate saw blades ^
! tool accepts most commonly available T-shank
and U-shank blades &
• When cutting metals, lubricate saw blade regularly with
oil
• For an accurate straight cut, guide tool with footplate
along the edge of a straight piece of wood *
• Pre-drill a hole before making cut-outs (
• Splinter-free cutting
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots F 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 96 dB(A) and the sound
power level 107 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
✱ when cutting wood 5.6 m/s²
✱ when cutting metal 3.0 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Scie sauteuse
INTRODUCTION
• Cet outil est conçu pour effectuer des découpes et
coupes dans le bois, les matières plastiques, le métal, les
plaques en céramique et le caoutchouc, et est approprié
pour des coupes droites et curvilignes avec des angles
d'onglet jusqu'à 45°
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Interrupteur pour mise en marche/arrêt
B Bouton de blocage de l'interrupteur
C Levier de sélection de mode de coupe
D Molette de réglage de la vitesse de sciage
E Interrupteur de soufflerie de poussières
F Fentes de ventilation
G Attache-câble
12
4381