Resetting The Digital Security Code; Troubleshooting - Sony SPP-Q110 Manual De Instrucciones

Note
Do not allow more than 20 seconds to elapse between each
step of the procedure.
Tips
• If you enter a wrong number, press (PGM), then start
from the beginning.
• You can attach the supplied directory on the handset.
• You can't receive calls while you're storing numbers.
To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in Step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2
Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1
Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
2
Press (SPEED DIAL).
3
Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.

Resetting the digital security code

The first time you charge the battery pack, a random security code is
automatically assigned between the base unit and the handset. Only a handset
which has this security code can make calls through the base unit. This system
prevents the possibility of other cordless telephone handsets making calls
through your base unit. You normally do not need to reset the security code.
However, in the unlikely event that you suspect that another cordless phone uses
the same security code, you can manually change the code. Pick up the handset
from the base unit, and proceed as follows:
TALK/BATT
LOW Lamp
Note
If the battery pack in the handset is completely discharged, or is removed
from the handset for more than several seconds, the digital security code
stored will be lost. If this happens, charge the battery pack and a new
security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset.
The code can be changed as often as desired.
Paging
You can page the handset from the base unit. Note that you can't
page if the handset is in use.
1
Press (PGM).
The TALK/BATT LOW lamp flashes.
2
Press (#).
You hear a confirmation beep.
3
Press three of the dialing keys (001 to
999) to store a new code.
4
Press (PGM).
You hear a long confirmation beep
and the TALK/BATT LOW lamp
goes off.
5
Immediately replace the handset on
the base unit
You hear a long confirmation beep
and the phone stores the new code.
To page
Press (PAGE).
The handset rings.
When you keep pressing (PAGE),
the handset rings continuously.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the
cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with
a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.

Troubleshooting

Make sure that you have set the voltage selector of the supplied AC power
adaptor to the correct position so that its voltage matches your local power
supply.
Problem
The handset does not make •Reset the digital security code.
or receive a call. •Place the base unit away from noise
sources such as TV, FM radio or PC.
•Make sure the base unit is connected to an
AC outlet.
•The battery pack may be discharged.
Charge the battery pack for about 12
hours.
You hear no dial tone. •Make sure the telephone line cord is
securely connected to the telephone outlet.
The handset doesn't •Make sure the dial mode setting (pulse or
connect at all, even the tone) is correct.
numbers you dial are
correct.
The handset does not redial •Make sure the number (including the tone
correctly. and pause digits, if used) you last dialed is
less than 32 digits.
The handset does not make
•Make sure there is a phone number
a speed dialing call.
correctly stored in the speed dialing.
•Store the desired phone number once
more.
The handset does not ring. •Make sure the base unit is connected to an
AC outlet.
The handset does not ring •The battery may have little or no power.
when paging from the base Charge the battery for more than 12
unit. hours.
•Extend the antenna of the base unit
vertically.
•Place the base unit away from noise
sources.
You hear a beep every 3 •Charge the battery pack for about 12
seconds and the TALK/ hours.
BATT LOW lamp flashes.
Specification
General
Frequency control Crystal-controlled PLL
Operation mode FM, duplex
Operation channel 25 channels
Supplied accessories AC power adaptor AC-T37 (1)
AC plug adaptor (1)
Telephone line cord (1)
Rechargeable battery pack BP-T16 (1)
Screws (2)
Directories (2 sheets)
Handset
Power source Rechargeable battery pack BP-T16
Battery life Standby: Approx. 14 days
Talk: Approx. 6 hours
Dimensions Approx. 59 x 201 x 59 mm (w/h/d), antenna
excluded
Antenna: 110 mm
Mass Approx. 230 g, battery included
Base unit
Power source DC 9V from AC power adaptor
Battery charging time Approx. 12 hours
Dimensions Approx. 148 x 58 x 233 mm (w/h/d), antenna
excluded
Antenna: 430 mm
Mass Approx. 345 g
Design and specifications are subject to change without notice.
Solution