Parts Identifi Cation (What Is What) - Husqvarna FS 513 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

A. Front Pointer: Use to Guide machine in a straight line.
B. Guide Wheel: On Front Pointer (A). Align to cutting
line and Blade (H) to produce straight cuts.
C. Blade Guard: Covers Blade (H). Must always be in
place when operating machine! Note tool direction as
marked on guard with an arrow.
D. Blade Guard Front: Part of Blade Guard. Can be
raised to install Blade (H).
E. Blade Guard Rear Bolt: Holds Blade Guard (C) in
position. Must be removed and relocated if Blade Guard
(C) is moved.
F. Blade Guard Latch Plate: Covers Outer Flange (J).
G. Water Hose Disconnect (G): Connects Blade Guard
(C) to Water Control Valve (KK1, KK2) or Water Tank (P).
Can be used when Blade Guard (C) is mounted to left or
right side of machine
H. Blade: Tool that cuts asphalt or concrete material – not
included with machine.
I. Inner Flange: Arbor on which the Blade (H) is mounted.
Replace if Damaged or worn.
J. Outer Flange: Used to hold Blade (H) in position.
Contains Locking Pin (K) that must go through Blade (H).
Replace if damaged or worn.
K. Locking Pin: Holds Blade (H) in position. Replace if
Damaged or worn.
L. Blade Shaft Nut (L1 / L2): Holds Outer Flange (J) to
machine. Nut (L1) on right side of machine has Left Hand
threads. Nut (L2) (not shown) on left side of machine has
Right Hand threads.
M. Blade Arbor: Blade (H) mounts on this surface.
N. Water Tank / Lifting Point Support: Holds Water Tank
(P). Supports Lifting Point (O).
14
PARTS IDENTIFICATION (WHAT IS WHAT)
O. Lifting Point: Lift machine only from this point!
P. Water Tank (If Equipped): 25 Liter (6.6 U.S. Gallon)
water capacity. Fill only with water! Do not fi ll with gaso-
line or other fl ammable substances! Use only for dust
suppression when cutting dry. Use only with laser welded
(dry) Diamond Blades (H).
Q. Engine Starting Rope (FS 513 Only): Use to start
engine. See engine operation manual.
R. Fuel Tank: Fuel fi ll point.
FS 520 / FS 524: Located at rear of machine. Fuel
fi ll is located on Left hand side of fuel tank.
FS 513: Located on engine - See engine operation
manual.
S. Engine Air Cleaner (FS 513 Shown): Check daily.
Clean every four (4) hours if cutting in dusty conditions.
See engine operation manual and maintenance section of
this document.
T. Blade Shaft Wrench (27mm): Use for installing and
removing Blade (H). Store in Tool Compartment (BB).
U. Wrench (13mm): Use for many maintenance items on
machine. Store in Tool Compartment (BB).
V. Front Cover: Clips to Water Tank Support (N). Open
to turn Engine Start Switch (DD) ON (1) or OFF (0) [FS
513 Only].
W. Shaft Guard: Protects Inner Flange (I). Always in-
stalled on opposite side of frame to Blade Guard (C).
X. Depth Control Grease Fitting: Not Shown. See Main-
tenance section of this document.
Y. Blade Guard Mounting Spade: Holds Blade Guard
(C) in position.
Z. Engine Oil Dipstick: Use to check engine oil level (Not
Shown – See Operation Section of this document).

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Fs 520Fs 524

Tabla de contenido