Flotec FPWF-WH2 Instrucciones De Instalación

P.O. Box 342, Delavan, WI 53115
Phone: 1-800-365-6832 • Fax: 1-800-526-3757
E-Mail: info@flotecwater.com • Web Site: http://www.flotecwater.com
2205 0196
Figure 1
2203 0196
Figure 2
F L
O W
2206 0196
Figure 3
F L
O W
2249 0196
Figure 3A
PRINTED IN U.S.A.
®
The system and installation must comply with all state and local laws and regulations.
"Do not use with water that is microbiologically unsafe or of unknown quality, with-
out adequate disinfection before or after the system."
Min./Max. operating pressure . . . . . . . . .138 kPa/862 kPa (20 psi/125 psi)
Min./Max. operating temperature . . . . . . . . . . .4.5°C/37.7°C (40°F/100°F)
Replacement cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FPWF-RS2
O-Ring Replacement kit . . . . . . . . . . . . . . . . . . . . . . . . . . . .FPWF-ORKit2
Do not allow system or system components to freeze; do not expose filter assembly to
direct sunlight (ultra violet light).
Step 1. After selecting the location where you will install your filter in the water line,
determine if existing shut off valves will isolate the filter housing during car-
tridge changes. It is important to have valves on both sides of the filter housing.
If you are installing the filter housing near the main water shut-off valve, you
may need to add only one additional valve just past the filter to prevent back
flow of water from the plumbing system during cartridge changing. Thread the
brass compression fittings or ball valves into the filter head using teflon tape
(Figure 1). Do not use joint compound. Tighten securely with a wrench but do
not overtighten.
Step 2. Turn off the water supply and drain the water lines by opening a faucet in an
upstairs sink in the house and one in the basement of the house. Measure and
cut the water line based on your individual installation (Figure 2).
Step 3. Slip the compression nut and appropriate ferrule on each end of the pipe. For
1/2-inch water line use the rubber ferrules, for 3/4-inch water line use the brass
ferrules (Figure 2).
Step 4. Slide the filter into position in the water line taking careful note of the proper
water flow direction (Figure 3). Use one wrench to hold the fitting that was
installed into the filter housing and tighten the nut with a second wrench. Turn
on the water supply and test for leaks. (Figure 3A is an alternate installation
showing the use of ball valves). Thoroughly flush the filter by running the water
for 30 minutes.
Step 5. Installations using metal pipe require a grounding jumper around the filter
(Figures 3, 3A). Use No. 4 AWG copper wire or larger. Grounding jumper must
meet code requirements.
When to change the filter cartridge
When the water flow is noticeably reduced it is time to change the cartridge. Generally
you should change the cartridge every 6 – 12 months, however, water conditions vary
greatly and you may need to change your cartridge more frequently.
Step 1. Close the gate valves on both sides of the filter and press the pressure release
button.
Step 2. Unscrew the filter canister and remove the cartridge. Inspect the
O-Ring and lubricate with petroleum jelly if necessary. For proper sealing the
O-Ring should be replaced every three cartridge changes.
Step 3. Replace the filter cartridge and reinstall the filter canister. Open the gate valves
on both sides of the filter and press the pressure release button to remove
trapped air.
For further operating, installation, or maintenance assistance:
Call Flotec Customer Service at
1-800-365-6832
Whole House Water Filters
MODEL FPWF-WH2
INSTALLATION INSTRUCTIONS
(cold water use only)
FP372 (Rev. 11/7/00)