Listening Through A Receiver (Home Theater); Troubleshooting For Anynet - Samsung PL-63P71FD Manual Del Usuario

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
Press the Anynet + button.
1
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
2 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3 Press the EXIT button to exit.
➢ When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical
jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the
Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI,
only 2 channel sound will be heard from the Home Theater receiver.
➢ If your receiver supports audio only, it may not appear in the device list.
➢ The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of
the TV.
➢ When using the WISELINK feature, sound may not output properly through the receiver.
When listening through the receiver, there are restrictions for using the PIP and audio-related menus.
➢

Troubleshooting for Anynet +

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on the
screen.
The Anynet + device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output through
the receiver.
BN68-01094N-Eng.indb 68
Solution
Check if the device is an Anynet + device. The Anynet + system supports Anynet + devices
■
only.
■ Connect only one receiver (home theater).
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
■
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work at a certain condition. (Searching channels, Operating WISELINK)
■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
Check if the Anynet + device is properly connected to the TV and check if the Anynet+
■
(HDMI-CEC) is set to On in the Anynet + Setup menu.
Press the TV button on the TV remote control to switch to TV. Then press the Anynet +
■
button to show the Anynet + menu and select a menu you want.
Select View TV in Anynet + menu.
■
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.
(Note that the channel button operates only when an Anynet + device with a built-in tuner
is not connected.)
You cannot use the remote control when you are configuring Anynet + or switching to a
■
view mode.
Use the remote control when the Anynet + setting or switching to view mode is complete.
■
■ You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet + functions.
■
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
You can connect an Anynet + device using the HDMI 1.3 cable only. Some HDMI cables
■
may not support Anynet + functions.
■ Check whether the antenna jack on the recording device is properly connected.
■ Connect the optical cable between TV and the receiver.
English - 68
TV Air 28
Recevier: Off
Connect DVDR
Setup
Move
Enter Exit
2007-04-27 ¿ÀÈÄ 3:09:22