Haier HSU-24HEK03/R2 Manual De Instalación
Ocultar thumbs Ver también para HSU-24HEK03/R2:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Manual of Room Air Conditioner
Preparation
Necessary Tools for Installation
Driver
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution
Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Drawing for the installation of indoor and outdoor units
The models adopt HFC free refrigerant R410A
more than 5cm
more than
10cm
Arrangement of piping
directions
Rear left
Rear
Left
right
Right
Below
more than 10cm
The marks from
to
A
in the figure are the
G
parts numbers.
The distance between
the indoor unit and the
floor should be more
than 2m.
more than
60cm
Please be subject to the actual product purchased , the above picture is just for your reference.
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual.
NO.0010526881
Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer
Attention must be paid to
the rising up of drain hose
more than 10cm
more than
10cm
Selection of Installation Place
Indoor Unit
Place, robust not causing vibration, where the body can be supported sufficiently.
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent lamps in the room are lightened.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is sufficiently ventilated.
Place, possible to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked
G
F
A
C
113.5
D
E
more than15cm
is available as illustrated in the above figure.
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
C
Connecting electric cable
D
for indoor and outdoor
E
Drain hose
F
Heating insulating material
G
Piping hole cover
Floor fixing dimensions of the
outdoor unit (Unit:mm)
113.5
633
Fixing of outdoor unit
Fix the unit to concrete or block
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
surface, roof or rooftop, fix
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
house, fix the unit by attaching a
vibration-proof mat.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Haier HSU-24HEK03/R2

  • Página 1 Installation Manual of Room Air Conditioner Preparation Necessary Tools for Installation Selection of Installation Place Torque wrench Indoor Unit Driver (17mm,22mm,26mm) Nipper Place, robust not causing vibration, where the body can be supported sufficiently. Hacksaw Pipe cutter Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the Hole core drill Flaring tool unit are not disturbed.
  • Página 2: Indoor Unit

    Accessory parts Installation of the Indoor Unit Drain hose (1) Remote controller (1) Drawing of pipe Cushion (4) R-03 dry battery (2) [ Rear piping ] Drain-elbow (1) Draw pipes and the drain hose, then fasten them with the adhesive tape Mounting plate (1) ・...
  • Página 3: Outdoor Unit

    Outdoor unit POWER connecting wiring: Indoor unit 3G0.75mm Indoor unit Outdoor unit Indoor unit Outdoor unit HSU-24HEK03/R2 ● Amax=15m Max.Elevation: HSU-24HEA03/R2 ● In case the elevation A is more Outdoor unit than 5m, oil trap shoud be installed every 5~7m Power cable: 3G2.5mm...
  • Página 4: Power Source Installation

    No gas leakage? On Drainage In case of gas leakage, tighten parts of pipe connection. If leakage stops, then proceed 6. steps Please install the drain hose so as to be downward slope without fail. Please don’t do the drainage as shown below. If it does not stop gas leakage, discharge whole refrigerants from the service port.
  • Página 5: Preparación

    Manual de instalación de aparato de aire acondicionado Preparación Herramientas necesarias para realizar la instalación Selección del lugar de instalación Unidad interior Destornillador Llave dinamométrica (17mm, 22mm, Coloque la unidad sobre una superficie que pueda soportarla correctamente y no 26mm) provoque vibraciones.
  • Página 6: Selección De Tubo

    1. Pase la manguera aislante a través del hueco de los materiales de aislamiento de Accesorios calor de la unidad interior. 2. Inserte los cables eléctricos de interior / exterior a través de la parte trasera de la unidad interior y tire de ellos desde la parte delantera. A continuación, conéctelos. 3.
  • Página 7 Unidad interior ALIMENTACIÓN Cable de alimentación: 3×0,75mm Unidad interior Unidad exterior HSU-24HEK03/R2 HSU-24HEA03/R2 cableado de conexión: 3×2,5mm Conexión 1. Si el cable de alimentación está dañado deberá ser reemplazado por el fabricante, Utilice el mismo método con la unidad interior. Afloje los tornillos del bloque de terminales e inserte los tapones completamente en los mismos.
  • Página 8: Etiqueta De Carga De Refrigerante

    Paso 1. Paso 2. Menos de Lateral de líquido de la válvula de 2 vías Lateral de gas de la válvula de 3 vías Abrir Se alza por la El extremo está Está ondulado. La separación con el Se aprecia mal olor de mitad.
  • Página 9: Selezione Del Luogo D'installazione

    Manuale d’ installazione del Condizionatore Preparazione Attrezzi necessari per l’’installazione Selezione del luogo d’installazione Unità interna Cacciavite Chiave dinamometrica (17mm, Installare in un luogo solido, senza vibrazioni, in grado di supportare il peso 22mm, 26mm) dell’unità. Luogo, non soggetto a calore o vapore generato nelle vicinanze, dove le prese e Pinza Tagliatubi gli scarichi dell’unità...
  • Página 10 Parti accessorie Installazione dell’unità interna Telecomando (1) Tubo di scarico (1) Schema della tubatura Batteria a secco R-03 (2) Cuscino (4) Piastra di montaggio (1) Giunto a gomito dello scarico (1) [Tubatura posteriore] Passare le tubature e lo scarico, poi fissarli con nastro adesivo [Tubatura sinistra –...
  • Página 11 Cavo d’ alimentazione: Condizionatore ≥ 3G× 0.75mm Condizionatore Unità da Condizionatore esterno Unità da esterno HSU-24HEK03/R2 HSU-24HEA03/R2 Elevazione massima: A massimo = Unità da esterno Se l’elevazione A è superiore ai 5m, un Cavi di collegamento: ≥ 3G 2.5mm ×...
  • Página 12 Aprire la valvola a stelo della valvola a 2 vie girandola in senso antiorario di 90 gradi. Dopo 6 secondi, chiudere la valvola a 2 vie ed eseguire un'ispezione per accertarsi che non ci siano perdite di gas. Non ci sono perdite di gas? Inclinato Danno della svasatura Rottura Parziale Troppo esterno Se ci sono perdite di gas, stringere i giunti del tubo.
  • Página 13: Source D'alimentation

    Manuel d'installation d'un climatiseur de pièce Préparation Outillage requis pour l'installation Sélection de l'emplacement pour l'installation Unité intérieure L'emplacement doit être solide sans vibration et offrir un support suffisant. Clé Clé dynamométrique (17 mm, 22 mm, L'emplacement ne doit pas être affecté par de la chaleur ou de la vapeur générées dans les 26 mm) environs et doit garantir que l'entrée et la sortie de l'unité...
  • Página 14 Accessoires Installation de l'unité intérieure Schéma de la tuyauterie é é l [Tuyauterie arrière] Batterie sèche R-03 (2) Coussinet (4) Acheminez les tuyaux et le tuyau de vidange que vous fixez ensuite avec du ruban adhésif. [Gauche - Tuyauterie arrière gauche] Dans le cas d'une tuyauterie à...
  • Página 15: Unité Extérieure

    Unité extérieure Connexion du câble avant l'installation de l'unité intérieure Installation de l’unité extérieure Insérez le cordon depuis l'arrière de l'unité et sortez par l'avant. Effectuez l'installation selon le schéma d'installation des unités intérieures et extérieures Desserrez les vis et enfoncez bien les extrémités du câble dans le bornier. Serrez les vis. Tirez légèrement sur le câble pour garantir qu'il a été...
  • Página 16 5. Pas de fuite de gaz? Vidange En cas de fuite de gaz, resserrez les pièces de connexion du tuyau. Lorsque la fuite est maîtrisée, passez à l'étape 6 Installez le tuyau de vidange de manière à ce que la pente soit descendante. Ne pas effectuer la vidange telle qu'illustrée ci-dessous.

Este manual también es adecuado para:

Hsu-24hea03/r2

Tabla de contenido