Makita CL111D Manual De Instrucciones página 12

3. Twist high performance filter in direction of arrow
to unfasten securing lip from cleaner unit and then pull
off the filter.
► Fig.13: 1. Securing lip
4. Clean out the fine dust and lightly tap to dislodge
dust from high performance filter.
Reassembly
Reassembly for normal filter
1. Put on filter until it is fully in position on the cleaner
unit.
► Fig.14: 1. Filter
► Fig.15: 1. Filter
NOTE: Make sure filter is put on straight without
being peeled back. If filter is put on incorrectly as
shown in diagram, dust will get into motor housing,
and cause motor failure.
2.
Connect prefilter. At this time, make sure to twist
prefilter so that securing lip is firmly locked into cleaner
unit.
► Fig.16: 1. Prefilter
► Fig.17
3. Connect capsule. Align O mark on capsule with O
mark on handle and then firmly twist capsule in direction
of arrow until it is secured.
► Fig.18: 1. O Mark
► Fig.19: 1. Handle 2. Capsule
NOTE: Always remove dust ahead of time, as suction
power will be reduced if there is too much dust in
cleaner.
NOTE: Always be sure to check that both filter and
prefilter are loaded correctly prior to using cleaner.
If they are not loaded correctly, dust will get into the
motor housing, and cause motor failure.
If the following examples occur, filter and prefilter are
not loaded correctly. Reload them correctly to rectify
problem.
Problem Examples
Example 1: Only prefilter has been loaded (no filter)
► Fig.20: 1. Prefilter
Example 2: Only filter has been loaded (no prefilter)
► Fig.21: 1. Filter
Example 3: Filter has been loaded in a peeled back
state
► Fig.22: 1. Filter
Example 4: Prefilter's securing lip is not firmly locked
into groove of cleaner housing
► Fig.23: 1. Groove of cleaner housing 2. Prefilter
3. Securing lip
Reassembly for high performance
filter
1. Connect high performance filter. At this time, make
sure to twist high performance filter so that securing lip
is firmly locked into cleaner unit.
► Fig.24: 1. High performance filter 2. Securing lip
► Fig.25: 1. Securing lip
2.
Connect capsule. Align O mark on capsule with O
mark on handle and then firmly twist capsule in direction
of arrow until it is secured.
► Fig.26: 1. O Mark
► Fig.27: 1. Handle 2. Capsule
NOTE: Always remove dust ahead of time, as suction
power will be reduced if there is too much dust in
cleaner.
NOTE: Always be sure to check that high perfor-
mance filter is loaded correctly prior to using cleaner.
If they are not loaded correctly, dust will get into the
motor housing, and cause motor failure.
If the following examples occur, high performance
filter is not loaded correctly. Reload them correctly to
rectify problem.
Problem Examples
Securing lip of high performance filter is not firmly
locked into groove of cleaner housing.
► Fig.28: 1. Securing lip 2. Groove of cleaner housing
OPERATION
CAUTION:
To connect attachments, such
as nozzle, twist and insert the attachment in
direction of the arrow to secure the connection
during use. To disconnect the attachments, twist
and extract it also in direction of the arrow. If an
attachment is twisted in the opposite direction when
being connected or disconnected, the capsule may
become loose.
► Fig.29: 1. Capsule
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.30: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.31: 1. Cleaner body 2. Extension wand
3. Nozzle
12 ENGLISH