Beko WMB 81242 PTMNX Manual Del Usuario página 16

5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the
rear of the machine and also at the end of each water intake
hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the
washing machine. Filters should be cleaned as they do get
dirty.
1. Close the taps.
2. Remove the nuts of the water intake hoses to access
the filters on the water intake valves. Clean them with an
appropriate brush. If the filters are too dirty, take them out
by means of pliers and clean them.
3. Take out the filters on the flat ends of the water intake
hoses together with the gaskets and clean thoroughly
under running water.
4. Replace the gaskets and filters carefully in their places
and tighten the hose nuts by hand.
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items
such as buttons, coins and fabric fibers clogging the pump
impeller during discharge of washing water. Thus, the water
will be discharged without any problem and the service life
of the pump will extend.
If the machine fails to drain water, the pump filter is clogged.
Filter must be cleaned whenever it is clogged or in every 3
months. Water must be drained off first to clean the pump
filter.
In addition, prior to transporting the machine (e.g., when
moving to another house) and in case of freezing of the
water, water may have to be drained completely.
:
A
Foreign substances left in the pump filter may
warning
damage your machine or may cause noise problem.
In order to clean the dirty filter and discharge the water:
1. Unplug the machine to cut off the supply power.
:
Temperature of the water inside the machine
A warning
may rise up to 90 ºC. To avoid burning risk, filter must be
cleaned after the water in the machine cools down.
2. Open the filter cap.
If the filter cap is composed of two pieces, press the
tab on the filter cap downwards and pull the piece out
towards yourself.
16 / 79 EN
All manuals and user guides at all-guides.com
If the filter cap is one piece, pull the cap from both sides at
the top to open.
C
3. Some of our products have emergency draining hose and
Discharging the water when the product has an emergency
draining hose:
a. Pull the emergency draining hose out from its seat
b. Place a large container at the end of the hose. Drain the
c. When draining of water is finished, close the end by the
d. Turn the pump filter to take it out.
Discharging the water when the product does not have an
emergency draining hose:
a. Place a large container in front of the filter to catch water
b. Loosen pump filter (anticlockwise) until water starts to
c. When the water inside the machine is finished, take out
4. Clean any residues inside the filter as well as fibers, if
5. Install the filter.
6. If the filter cap is composed of two pieces, close the filter
You can remove the filter cover by slightly pushing
downwards with a thin plastic tipped tool, through the
gap above the filter cover. Do not use metal tipped tools
to remove the cover.
some does not have. Follow the steps below to discharge
the water.
water into the container by pulling out the plug at the end
of the hose. When the container is full, block the inlet
of the hose by replacing the plug. After the container is
emptied, repeat the above procedure to drain the water in
the machine completely.
plug again and fix the hose in its place.
from the filter.
flow. Fill the flowing water into the container you have
placed in front of the filter. Always keep a piece of cloth
handy to absorb any spilled water.
the filter completely by turning it.
any, around the pump impeller region.
cap by pressing on the tab. If it is one piece, seat the tabs
in the lower part into their places first, and then press the
upper part to close.
Washing Machine / User's Manual