Appropriate Installation Location; Connecting Water Supply - Beko WMB 81242 PTMNX Manual Del Usuario

1.6 Compliance with WEEE Directive
This appliance's packaging material is
recyclable. Help recycle it and protect the
environment by dropping it off in the municipal
receptacles provided for this purpose. Your
appliance also contains a great amount of
recyclable material. It is marked with this label
to indicate the used appliances that should not
be mixed with other waste. This way, the appliance recycling
organised by your manufacturer will be done under the best
possible conditions, in compliance with European Directive
2002/96/EC on Waste Electrical and Electronic Equipment.
Contact your town hall or your retailer for the used appliance
collection points closest to your home. We thank you doing
your part to protect the environment.
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparation of the location and electrical, tap water and
waste water installations at the place of installation is
under customer's responsibility.
B :
Installation and electrical connections of
warning
the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by
unauthorized persons.
A :
Prior to installation, visually check if the product
warning
has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
C
Make sure that the water inlet and discharge hoses
as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after
installation or cleaning procedures.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a
long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature
may fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
3 / 79 EN
All manuals and user guides at all-guides.com
2.3 Removing the transportation locks
A
A
1. Loosen all the bolts with a suitable spanner until they
2. Remove transportation safety bolts by turning them
3. Attach the plastic covers supplied in the User Manual bag
C
C

2.4 Connecting water supply

C
C
A
A
1. Connect the special hoses supplied with the product to
:
Do not remove the transportation locks before
warning
taking out the packaging reinforcement.
:
Remove the transportation safety bolts before
warning
operating the washing machine! Otherwise, the product
will be damaged.
rotate freely (C) .
gently.
into the holes on the rear panel. (P)
Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved
again in the future.
Never move the product without the transportation safety
bolts properly fixed in place!
The water supply pressure required to run the product is
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
have 10 – 80 liters of water flowing from the fully open
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.
If you are going to use the double water-inlet product
(cold)
as a single water-inlet unit, you must install the
supplied stopper to the hot water valve before operating
the product. (Applies for the products supplied with a
blind stopper group.)
:
Models with a single water inlet should not be
warning
connected to the hot water tap. In such a case the laundry
will get damaged or the product will switch to protection
mode and will not operate.
:
Do not use old or used water inlet hoses on the
warning
new product. It may cause stains on your laundry.
the water inlets on the product. Red hose (left) (max. 90
ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is
for cold water inlet.
Washing Machine / User's Manual