Alarm Settings; Using The Aux Input - Denver DAB-36 Manual Del Usuario

The station order can be by alphanumeric or ensemble.
5. Prune (Yes/No)
Yes- this removes all invalid stations.
No- Keep all stations.
6. System
Time
Ⅰ. Set Time/Date
Ⅱ. Auto Update
Ⅲ. Set 12/24 hour format
Ⅳ. Set Date format
Backlight
Ⅰ. Timout
Ⅱ. On level
Ⅲ. Dimmer level
Languages
Factory Reset
Choose "YES" to clear all settings
SW version
B. On FM Mode. Press MENU button and tune "TUNE/SELECT" knob to see the available types,
Press MENU again to return back.
1. Scan Setting
To select the Strong stations or All stations.
2. Audio Setting
To select Forced mono or Stereo allowed
3. System
Time
Ⅰ. Set Time/Date
Ⅱ. Auto Update
Ⅲ. Set 12/24 hour format
Ⅳ. Set Date format
Backlight
Ⅰ. Timout
Ⅱ. On level
Ⅲ. Dimmer level
Languages
Factory Reset
Choose "YES" to clear all settings
SW version
INFO Button
A. On DAB Mode, The UNIT has DAB information modes which are shown on the bottom line of the
display. Press INFO button to see the available information.
B. On FM Mode, The UNIT has FM information modes which are shown on the bottom line of the
display. Press INFO button to see the available information.
ENG 5

ALARM SETTINGS

Alarms will only function when the unit is On (mains or battery power) or in Standby mode (Mains
power only).
Alarms can be switched on or off in standby mode (see below), however, the alarm parameters can
only be set when the unit is on.
To set alarms
Turn the unit on.
To set or change alarm 1, press "ALARM" once, then press "TUNE/SELECT". To set or change alarm
2, press "ALARM" twice, then press "TUNE/SELECT". To exit alarm setting mode, press "ALARM"
again.
The alarm setup prompts you for the following parameters. Select a value for each parameter in turn
turning the "TUNE/SELECT" knob and press "TUNE/SELECT" to confirm and move on to the next
parameter.
Parameters
● On time – hours and minutes
● Duration – 15 / 30 / 45 / 60 / 90minutes
If the alarm is not cancelled the unit returns to standby after this time period.
● Source – Buzzer/DAB/FM
If DAB or FM is chosen as the audio source you will also be prompted to select the Last played station
or one of the preset stations (if set).
● Daily / Once / Weekends / Weekdays
Choose the days on which the alarm is active.
Note: if you choose 'Once', you are prompted to enter the required date.
● Alarm – Off/On

USING THE AUX INPUT

Connect the AUX connect wire from the out jack of your Personal Player such as portable MP3 player
to the AUX input jack.
Press the DAB/FM/AUX/BT button to select AUX mode, "Auxiliary Input" will show on the LCD.
Turn on your Personal Player to begin playing, adjust the volume to desire listening level.
IN Bluetooth MODE
Press the DAB/FM/AUX/BT button to select BLUETOOTH mode, LCD showing "Smart Device".
To pair the radio with your phone:
Turn on the Bluetooth function in the phone or tablet. For instructions, see your mobile phone user
guide.
a. Place the phone within 20 cm (8 inches) of the radio.
b. Please make sure the radio is in BT mode. Choose "DAB-36" on your phone to connect the
radio Bluetooth. After connected, your radio will show "BT Connected".
c. Enjoy your music with the radio now!
Hereby, Inter Sales A/S declares that the radio equipment type DAB-36 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet
address: http://www.denver-electronics.com/denver-dab-36/
ENG 6