Worx WX106L Manual Del Usuario página 6

recommended for your power tool and only
for recommended applications. For example:
do not grind with the side of a cut-off
wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these
wheels may cause them to shatter.
b) For threaded abrasive cones and plugs
use only undamaged wheel mandrels with
an unrelieved shoulder flange that are of
correct size and length. Proper mandrels will
reduce the possibility of breakage.
c) Do not "jam" a cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility to
twisting or snagging of the wheel in the cut and
the possibility of kickback or wheel breakage.
d) Do not position your hand in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel the
spinning wheel and the power tool directly at you.
e) When wheel is pinched, snagged or when
interrupting a cut for any reason, switch
off the power tool and hold the power tool
motionless until the wheel comes to a
complete stop. Never attempt to remove
the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may
occur. Investigate and take corrective action
to eliminate the cause of wheel pinching or
6
snagging.
f) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power tool is
restarted in the workpiece.
g) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag
under their own weight. Supports must be
placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides
of the wheel.
h) Use extra caution when making a "pocket
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.
Safety Warnings Specific for Wire Brushing
Operations:
a) Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire bristles
can easily penetrate light clothing and/or skin.
b) Allow brushes to run at operating speed
for at least one minute before using them.
During this time no one is to stand in front
or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
c) Direct the discharge of the spinning wire
Rotary tool
brush away from you. Small particles and
tiny wire fragments may be discharged at high
velocity during the use of these brushes and may
become imbedded in your skin.
SAFETY WARNINGS FOR
BATTERY CELLS INSIDE
THE TOOL
a) Do not dismantle, open or shred cells.
b) Do not short-circuit charging terminal. Do
not store power tool haphazardly in a box or
drawer where charging terminal may short-
circuit each other or be short-circuited by
conductive materials. When power tool is
not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that
can make a connection from one charging
terminal to another.
c) Do not expose power tool to heat or fire.
Avoid storage in direct sunlight.
d) Do not subject power tool to mechanical
shock.
e) In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has been
made, wash the affected area with copious
amounts of water and seek medical advice.
f) Keep power tool clean and dry.
g) Wipe the charging terminals with a clean
dry cloth if they become dirty.
h) Power tool needs to be charged before use.
Always refer to this instruction and use the
correct charging procedure.
i) Do not maintain power tool on charge when
not in use.
j) After extended periods of storage, it may
be necessary to charge and discharge
the power tool several times to obtain
maximum performance.
k) Recharge only with the charger specified
by Worx. Do not use any charger other than
that specifically provided for use with the
equipment.
l) Keep power tool out of the reach of
children.
m) Retain the original product literature for
future reference.
n) Dispose of properly.
o) Do not mix cells of different manufacture,
capacity, size or type within a device.
p) Do not use any cell which is not designed
for use with the equipment.
q) Keep the battery away from microwaves
and high pressure.
EN