Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Disconnect the plug from the supply.
•
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
•
Only fi t 13 Amperes BS1363A approved plugs
fi tted with the correctly rated fuse (1).
•
The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to their
respective points in the plug (see below).
Brown is for Live (L) (2) and Blue is for Neutral
(N) (4).
•
Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is
holding the outer sheath of the cable fi rmly
and that the two leads are correctly fi xed at the
terminal screws.
WARNING: Never use a light socket. Never
connect the live (L) or neutral (N) wires to
the earth pin marked E or
For 115 V units with a power rating exceeding
1500 W, we recommend to fi t a plug to BS4343
standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
All manuals and user guides at all-guides.com
.
Cable rating (Amperes)
6
10
15
20
25
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
WA R N I N G: P r i o r t o a s s e m b l y a n d
adjustment always unplug the tool.
MOUNTING AND REMOVING THE GUARD
(FIG. B)
KEYLESS GUARD (FIG. B)
•
Place the angle grinder on a table, spindle up.
•
Release the clamping lock (8) and hold the
guard (3) over the tool as shown.
•
Align the lugs (5) with the notches (6).
•
Press the guard down and rotate it to the
required position.
•
If required, increase the clamping force by
tightening the screw (9).
•
Tighten the clamping lock.
•
To remove the guard, release the clamping
lock.
WARNING: Never use the tool without the
guard in place.
FITTING AND REMOVING A GRINDING OR
CUTTING DISC (FIG. C1 & C2)
•
Place the tool on a table, guard up.
•
Fit the inner fl ange (10) correctly onto the
spindle (11) (fi g. C1).
•
Place the disc (12) on the fl ange (10). When
fi tting a disc with a raised center, make sure
that the raised centre (13) is facing the fl ange
(10).
•
Screw the outer fl ange (14) onto the spindle
(11) (fi g. C2):
–
the ring on the fl ange (14) must face towards
the disc when fi tting a grinding disc (A);
–
the ring on the fl ange (14) must face away
from the disc when fi tting a cutting disc (B).
E N G L I S H
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
60
6
10
15
20
25
-
-
-
6
6
6
6
15
15
20
-
55
Publicidad
Tabla de contenido
