Milwaukee M12 FUEL Manual Del Operador página 6

OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the tool will not
run. Allow the battery to cool down.
Using the Mode Selector
The mode selector button is used to
adjust the rotation speed (RPM) for
the application.
To select the mode:
1. Push the switch lock-off forward
then squeeze and release the
paddle switch. The current mode
indicator number is lit.
2. Press the mode selector button
to cycle through the 4 modes. When the desired
mode indicator number is lit, begin work.
Mode 1
RPM 0 - 10,000 0 - 15,000 0 - 20,000 0 - 24,500
General Operation
1. If you have just installed an accessory or are
beginning a period of work, test it by letting it spin
for one minute before applying it to the workpiece.
WARNING! Never use an accessory that has been
dropped. Out-of-balance or damaged accessories
can mar workpiece, damage the tool, and cause
stress that may cause accessory failure.
2. Use a clamp, vise or other practical means to hold
your work.
3. To start the tool, push the switch lock-off forward
(1) and squeeze the paddle switch (2). NOTE: An
LED is turned on when the switch is pulled.
2
4. Allow accessory to come to full speed before
beginning work.
5. To vary the speed, increase or decrease pressure
on the switch. The further the switch is pulled, the
greater the speed.
6. Control pressure and surface contact between ac-
2 3
1
cessory and workpiece. WARNING! Never bang
accessories onto work.Too much pressure causes
accessory failure or slows speed.
7. To stop the tool, release the switch. Make sure the tool
comes to a complete stop before laying the tool down.
If the grinder begins vibrating, immediately stop
the motor and check to see if the accessory
is dull. Dull accessories will cause the tool to
vibrate and could force the collet to fly off the
tool. Always replace or sharpen dull accessories.
Accessories are design for specific uses. Only use
points, cones, plugs, grinding wheels and cut-off
wheels for applications for which they were designed.
Follow manufacturer's care and use instructions.
WARNING
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
4
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
WARNING
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.
WARNING
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
6
MAINTENANCE
To reduce the risk of injury, always
unplug the charger and remove the
Maintaining Tool
To reduce the risk of personal in-
jury and damage, never immerse
Cleaning
Repairs
ACCESSORIES
Use only recommended accesso-
ries. Others may be hazardous.