gefran 40T 48 Manual De Uso página 13

Input
I n
settings
Type of probe,
signal and scale of
main input
TYPE Type 4 DIGIT
PROBE
without dec. point with dec. point
Probe: TC
0 TC J °C 0/1000 0.0/999.9
1 TC J °F 32/1832 32.0/999.9
2 TC K °C 0/1300 0.0/999.9
3 TC K °F 32/2372 32.0/999.9
4 TC R °C 0/1750 0.0/999.9
5 TC R °F 32/3182 32.0/999.9
6 TC S °C 0/1750 0.0/999.9
7 TC S °F 32/3182 32.0/999.9
8 TC T °C -200/400 -199.9/400.0
9 TC T °F -328/752 -199.9/752.0
10 TC B °C 44/1800 44.0/999.9
11 TC B °F 111/3272 111.0/999.9
12 TC E °C -100/750 -100.0/750.0
13 TC E °F -148/1382 -148.0/999.9
14 TC N °C 0/1300 0.0/999.9
15 TC N °F 32/2372 32.0/999.9
16 TC L °C 0/600 0.0/600.0
17 TC L °F 32/1112 32.0/999.9
18 TC U °C -200/400 -199.9/400.0
19 TC U °F -328/752 -199.9/752.0
20 TC G °C 0/2300 0.0/999.9
21 TC G °F 32/4172 32.0/999.9
22 TC D °C 0/2300 0.0/999.9
23 TC D °F 32/4172 32.0/999.9
24 TC C °C 0/2300 0.0/999.9
25 TC C °F 32/4172 32.0/999.9
26 TC °C Custom
27 TC °F Custom
Probe: RTD
28 PT100 °C -200/600 -199.9/600.0
29 PT100 °F -328/1112 -199.9/999.9
30 JPT100 °C -200/600 -199.9/600.0
31 JPT100 °F -328/1112 -199.9/999.9
Probe: PTC - NTC
32 PTC °C -55/120 -55.0/120.0
33 PTC °F -67/248 -67.0/248.0
34 NTC °C -10/70 -10.0/70.0
35 NTC °F 14/158 14.0/158.0
Probe: Voltage + Current
36 0...60mV -1999/9999 -199.9/999.9
37 0...60mV linear custom linear custom
38 12...60mV -1999/9999 -199.9/999.9
39 12...60mV linear custom linear custom
40 0...20mA -1999/9999 -199.9/999.9
41 0...20mA linear custom linear custom
42 4...20mA -1999/9999 -199.9/999.9
43 4...20mA linear custom linear custom
44 0...10V -1999/9999 -199.9/999.9
45 0...10V linear custom linear custom
46 2...10V -1999/9999 -199.9/999.9
47 2...10V linear custom linear custom
48 0...5V -1999/9999 -199.9/999.9
49 0...5V linear custom linear custom
50 1...5V -1999/9999 -199.9/999.9
51 1...5V linear custom linear custom
52 0...1V -1999/9999 -199.9/999.9
53 0...1V linear custom linear custom
54 200mV...1V -1999/9999 -199.9/999.9
55 200mV...1V linear custom linear custom
Probe: Custom PT100 - PTC - NTC
56 PT100 custom
JPT
57 PTC custom
58 NTC custom
In case of non-availability, maximum and minimum limits are set to 0.
In case of custom linearization, test limits for setting LO and HI errors are given by the
calibration values.
If these limits are not exceeded, they are taken into consideration as limits LO_S and
HI_S.
Max. non-linearity error for
thermocouples (TC),
resistors (PT100) and
thermistors (PTC, NTC).
The error is calculated as deviation from
theoretical value and is expressed as
percentage of full scale (in °C).
• TC/LIN input parameters
3 DIGIT + sign
(model 96 only)
without dec. point with dec. point
0/999 0.0/99.9
32/999 32.0/99.9
0/999 0.0/99.9
32/999 32.0/99.9
0/999 0.0/99.9
32/999 32.0/99.9
0/999 0.0/99.9
32/999 32.0/99.9
-200/400 -99.9/99.9
-328/752 -99.9/99.9
not available not available
not available not available
-100/750 not available
-148/999 not available
0/999 not available
32/999 not available
0/600 0.0/99.9
32/999 32.0/99.9
-200/400 -99.9/99.9
-328/752 -99.9/99.9
0/999 not available
32/999 not available
0/999 not available
32/999 not available
0/999 not available
32/999 not available
Custom Custom Custom
Custom Custom Custom
-200/600 -99.9/99.9
-328/999 -99.9/99.9
-200/600 -99.9/99.9
-328/999 -99.9/99.9
-55/120 -55.0/99.9
-67/248 -67.0/99.9
-10/70 -10.0/70.0
14/158 14.0/99.9
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
-999/999 -99.9/99.9
linear custom linear custom
custom custom custom
custom custom custom
custom custom custom
S, R range 0...1750°C; error < 0.2% f.s. (t > 300°C) / for other range; error < 0.5% f.s.
T error < 0.2% f.s. (t > -150°C)
B range 44...1800°C; error < 0.5% f.s. (t > 300°C) / range 44,0...999,9; error < 1% f.s. (t > 300°C)
U range -99,9...99,9 and -99...99°C; error < 0.5% f.s. / for other range; error < 0.2% f.s. (t > -150°C)
G error < 0.2% f.s. (t > 300°C)
D error < 0.2% f.s. (t > 200°C)
C range 0...2300; error < 0.2% f.s. / for other range; error < 0.5% f.s.
NTC error < 0.5% f.s.
Tc: J, K, E, N, L error < 0.2% f.s.
PT100, JPT100 and PTC error < 0.2% f.s.
Select sampling time
(resolution). For linear
input only.
Digital filter
on main input
Digital filter on process
variable display
Decimal point position for
main input scale
Minimum limit of main
input scale
and analogue output
Maximum limit of main
input scale
and analogue output
Offset correction
of main input
Select function of
digital input
Raise key function
(active only in
P.V.selection)
Lower key function
(active only in
P.V.selection)
Low limit for the alarms
set point
High limit for
the alarms set point
13
0 120ms > 13bit; 8000 divs
1 60ms > 13bit; 8000 divs
2 30ms > 12bit; 4000 divs
3 15ms > 11bit; 2000 divs
+4 to disable filter (average
of the last eight values sampled)
0.0 ... 20.0 sec
0.0 ... 9.9
scale points
dP Format
0 XXXX
1 XXX.X
2 * XX.XX
3 * X.XXX
(*) not available for TC,
RTD, PTC and NTC scales
min...max scale
of input selected in t.P
min...max scale
of input selected in t.P
-999 ...999
scale points
d. i. - t. u. - t. d.
0 None
1 Zero
2 Hold
3 Flash
4 Max. peak display
5 Min. peak display
6 Delta peak display
7 Peak memory reset
8 Zero + peak memory reset
9 Alarms reset
10 Peak + alarms reset
11 Zero + alarms reset
12 Peak + zero + alarms reset
13 Output status OUT1
14 Output status OUT2
15 Output status OUT3
L.S ... H.S
L.S ... H.S