Tabla de contenido
Publicidad
GB
English
Quick Reference Manual
Mount new timer
For installation in drywall, use drywall anchors (included in
package). If possible, locate the timer within 1.8m of an AC outlet
and at least 4.6m away from major appliances or air conditioners.
Connect zone wires
A. Connect Colored Zone Wires from each ZONE
valve to the corresponding ZONE number on the
timer terminal block. Refer to your photo of the old
timer's wiring.
B. Connect the White Common Wire to the COMMON
(C) terminal.
NOTE: Install two AAA batteries to
retain date and time in the event of
a power outage.
Warning: Insulate properly from any
shared wiring in conduit.
Connect power wires
Route the transformer power cord through the conduit opening at the bottom
of the unit. Connect the two end wires on the power cord to the two 24VAC
terminal connections on the timer. Do not remove the yellow jumper wire on
the terminals marked SENS.
Warning: DO NOT plug in the transformer or turn on power until you have
completed and checked all wiring connections.
Warning: Wiring must comply with local codes.
Programming at the timer
Auto Auto is the normal operating mode
Press the AUTO key to return to normal
operation. During watering, the display shows
a blinking sprinkler symbol, the active ZONE
number and watering RUN TIME remaining
for that zone.
Rain Delay — Up to 14 Days Press and hold
the + button. The number of days along with the stop icon will be
displayed.
• Press + or – to increase or decrease the rain delay.
• After rain delay has elapsed, watering will automatically resume.
Date/Time Set current date and time
• Press the DATE/TIME key.
• Press + or – to adjust the current selection.
• Press NEXT (or BACK) to select the value you
wish to change.
Zone Schedule Create irrigation schedules
Press the zone SCHEDULE key, then follow
steps 1 through 4.
1
Select Zone: Press + or – to select
desired ZONE number; then press NEXT.
2
Set Watering Run Time: Press
+ or – to set desired RUN TIME ;
then press NEXT.
3
Set Watering Start Times: Press + or – to set first START TIME; then
press NEXT.
REPEAT as desired to set additional START TIMES for that zone.
NOTE: Pressing NEXT with -:- (OFF) is blinking on the display will
advance to Step 4.
NOTE: Watering START TIMES automatically stack.
4
Set Watering Start Days: Press + or – to select one of four available
options:
4-a
Custom Days
• Press + or – to select
then press NEXT.
• Press ON (to enable) or OFF (to disable) the blinking SELECTION DAY.
Cursor will then advance to the next SELECTION DAY.
REPEAT for each day of the week as desired.
4-b
Odd Days
Press + or - to select
4-c
Even Days
Press + or – to select
4-d
Cyclic Days
• Press + or – to select
• Press + or – to set desired DAY CYCLE; then press NEXT.
• Press + or – to set desired START DATE; then press NEXT.
REPEAT steps 1–4 for additional zones as desired.
8
183997-01,09JL20,MANUAL,RZXe,ManualOperation.indd 8
24VAC
SENS
C M
1
2
3
4
5
6
7
8
ACCESSORY
MIN
4
1
2
then press NEXT.
then press NEXT.
then press NEXT.
THEN
Manual Watering Start watering immediately
• Press the MANUAL watering key.
• Press + or – to select ALL zones or any
SINGLE zone; then press NEXT.
• Press + or – to set desired RUN TIME; then
press NEXT to begin watering.
NOTE: Only stations with programmed RUN
TIMES and START TIMES will water manually.
NOTE: To stop manual watering, press the OFF key to stop irrigation and
then press the AUTO key to return to normal operation.
NOTE: If ALL zones are watering, pressing NEXT will advance watering
to next zone.
Seasonal Adjust Increase or decrease watering duration (Run Times)
for all Zones.
• Press the SEASONAL ADJUST button
• Press + or – to increase or decrease the SEASONAL ADJUST percentage
setting.
NOTE: The SEASONAL ADJUST value can be
adjusted from -90% to +100%. For example,
a +50% adjustment means a Run Time of 10
minutes will become 15 minutes.
NOTE: SEASONAL ADJUST applies to ALL
programmed irrigation schedules.
Press AUTO to resume normal operation.
Off Stops all irrigation
• Press the OFF key to immediately cancel all active watering. No
automatic irrigation will occur when the system is in OFF.
• Programmed irrigation schedules still remain stored in memory even
when the controller is turned off or if power is lost.
NOTE: Press the AUTO key to resume normal operation. Automatic
irrigation will NOT occur if the controller remains in OFF mode.
Rain Sensor Bypass
Set controller to OBEY or IGNORE a Rain Sensor.
Set Bypass for One Zone
• Press the SCHEDULE key.
• Press + or – to select the desired Zone number.
• Press and release both BACK and NEXT keys at the same time to toggle
between OBEY and IGNORE.
SYMBOL is displayed when IGNORE is selected.
Set Bypass for All Zones
• Press the AUTO key.
• Press and release both BACK and NEXT keys at the same time to toggle
between OBEY and IGNORE.
SYMBOL is displayed when IGNORE is selected.
3
FR
Aid
Inst
Pou
pou
MIN
min
au m
clim
Con
A. C
v
s
à
B. C
C
REM
pou
cas
Ave
tou
Con
Fait
Setting
con
d'al
reti
Ave
cou
Ave
Pro
7/9/20 12:16 PM
Publicidad
Tabla de contenido
