Introduction; Device Description; Scope Of Delivery - Parkside PTK 2000 A1 Instrucciones De Servicio Y Seguridad

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan-
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about
the associated dangers. The minimum age requirement
must be complied with. In addition to the safety require-
ments in these operating instructions and your country's
applicable regulations, you should observe the generally
recognized technical rules concerning the operation of
woodworking machines.
48 GB
2. La
yout
(Fig.1/2/4/9-10/16-18/20/28/31)
1. Saw bench
2. Saw blade guard
3. Extraction hose
4. Splitter
5. Saw blade
6. Table insert
7. Parallel stop
8. Hand wheel
9. Adjusting and locking grip
10. Base frame
11. ON/OFF switch
12. Chain bar
13. Cross stop
14. Bench width extension
15. Bench length extension
16. Extractor adapter
17. Push stick
18. Legs
19. Cross struts
20. Longitudinal struts
21. Center struts, short
22. Center struts, long
23. Rubber legs
24. Stability bar
25. Table support, short
26. Table support, long
27. Screw with wing nut
28. Oval hole in splitter
29. Countersunk head screws
30. Fixing screw
31. Eccentric lever
32. Groove
33. Knurled screw
34. Laser
35. Laser switch
36. Screws for battery compartment
37. Battery cover
38. /39. Fixing points

3. Scope of delivery

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• Original operating instructions
• Saw table to preassembled,
- carbide-tipped saw blade with 24 teeth
• Carbide-tipped saw blade with 48 teeth
• Saw blade guard
• Extraction hose
• Splitter with laser
• Batteries 1.5 V AAA (2x)
• Parallel stop
• Stop rail
• Cross stop
• Table width extension (2x)