Maintenance And Service - stayer S90PE Manual De Instrucciones

- As soon as the saw foot lies smoothly on the workpiece,
you can begin sawing.
Sawing out areas
- With a drill, drill a sufficiently large hole inside of the area to
be sawed out.
- Guide the saw blade (11) into this hole and begin to saw out
the desired area.
- Use the laser guide (14) to obtain more precise cuts.
Mounting the parallel guide
The parallel lines can be sawed with miter-precise intervals
using a parallel guide (19). Parallel cuts are only available
when the angle of the saw foot is set to 0° and the plastic
cover for sawfoot (27) is removed.
- Using screwdriver loosen the tightening screw of the
parallel guide (20).
- Push the parallel guide into the guideway opening (24).
The parallel guide can be inserted in the left or right side
of the power tool.
- Align the guide rail and retighten the tightening screw
(20).
Laser guide
S110PE/S90PE
DANGER LASER RADIATION
Do not look directly into the beam. Laser
specification according to EN2841-1:
CLASS 2. Wavelength: 650mm / Power:
<1mW
The built-in laser guide is intended to obtain a precision cut.
Use the laser guide (14) every time the work requires
precision cuts, as when following pre-drawn lines on a
surface.
- Set the I/O laser switch (16) to the position I to activate
the laser guide (14).
- Press the On/Off switch (2), and start cutting the
workpiece following the predrawn linewith the projected
laser line on the surface.
Metal cutting
When sawing metal, because of the heating up of the
material, apply e.g. a cool lubricant along the cutline.
- Lightly grease the cut-line with suitable oil.

Maintenance and Service

Maintenance and Cleaning.
- Before any work on the machine itself, pull the mains
plug.
- For safe and proper working, always keep the
machine and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the
saw blade from the machine and lightly tap out the machine
on a level surface.
Heavy contamination of the machine can lead to
malfunctions. Therefore, do not saw materials that produce
a lot of dust from below or overhead.
ENGLISH
25
- In extreme working conditions, conductive dust
can accumulate in the interior of the machine when
working with metal. The protective insulation of the
machine can be degraded. The use of a stationary
extraction system is recommended in such cases as
well as frequently blowing out the ventilation slots
and installing a residual current device (RCD).
Lubricate the guide roller (10) occasionally with a drop of
oil. Check the guide roller (10) regularly. If worn, it must be
replaced through an authorised Stayer after-sales service
agent.
WARNING! Important instructions for connecting a
new 3-pin plug to the 2-wire cable. The wires in the
cable are coloured according to the following code:
Do not connect the blue or brown wire to the earth terminal
of the plug.
Important: If for any reason the moulded plug is removed
from the cable of this power tool, it must be disposed of
safely.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for Stayer
power tools.
Transport
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user can
transport the batteries by road without further requirements.
When being transported by third parties (e.g.: air transport
or forwarding agency), special requirements on packaging
and labelling must be observed. For preparation of the
item being shipped, consulting an expert for hazardous
material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations.
After-sales Service
Our after-sales service responds to your questions
concerningmaintenance and repair of your product as well
as spare parts. Exploded views and information on spare
parts can also be found under:
www.grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
25