HIKVISION PanoVu PT Serie Guia De Inicio Rapido página 23

to your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info
2006/66/EC and its amendment 2013/56/EU
(battery directive): This product contains a
battery that cannot be disposed of as unsorted
municipal waste in the European Union. See
the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection
point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
KC
이 기기는 업무용 환경에서 사용할 목적으로
적합성평가를 받은 기기로서 가정용 환경에서
사용하는 경우 전파간섭의 우려가 있습니다.
Warning
This is a class A product. In a domestic environment this
product may cause radio inter-ference in which case the
user may be required to take adequate measures.
Safety Instructions
Warnings
Laws and Regulations
The device should be used in compliance with local laws,
electrical safety regulations, and fire prevention regulations.
Electrical Safety
CAUTION: To reduce the risk of fire, replace only with the
same type and rating of fuse.
Battery
Do not ingest battery. Chemical burn hazard!
This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop
using the product and keep it away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
CAUTION: Risk of explosion if the battery is replaced by
an incorrect type.
Improper replacement of the battery with an incorrect
type may defeat a safeguard (for example, in the case of
some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in
an explosion.
Do not leave the battery in an extremely high
temperature surrounding environment, which may result
in an explosion or the leakage of flammable liquid or gas.
Do not subject the battery to extremely low air pressure,
which may result in an explosion or the leakage of
flammable liquid or gas.
Dispose of used batteries according to the instructions.
Cautions
Fire Prevention
No naked flame sources, such as lighted candles, should
be placed on the equipment.
The serial port of the equipment is used for debugging only.
Hot Surface
CAUTION: Hot parts! Burned fingers when handling the parts.
This sticker is to indicate that the
marked item can be hot and should
not be touched without taking care.
Wait one-half hour after switching
off before handling parts.
The device with this sticker is intended for installation in
a restricted access location. Access can only be gained
by service persons or by users who have been instructed
about the reasons for the restrictions applied to the
location and about any precautions that shall be taken.
Installation
Install the equipment according to the instructions in this
manual.
To prevent injury, this equipment must be securely
attached to the ceiling/wall in accordance with the
installation instructions.
We recommend you to adjust the horizontal angel to
-10° for wall mounting to get a better view.
Be sure that there is enough space to install the camera
and accessories.
Make sure that the wall is strong enough to withstand at
least 8 times the weight of the camera and the mount.
Make sure that the power has been disconnected before
you wire, install, or disassemble the device.
Transportation
Keep the device in original or similar packaging while
transporting it.
Power Supply
The power source should meet limited power source or
PS2 requirements according to IEC 60950-1 or
IEC 62368-1 standard.
Refer to camera label for the standard power supply.
Please make sure your power supply matches with
your camera.
DO NOT connect multiple devices to one power adapter,
to avoid over-heating or fire hazards caused by overload.
System Security
Please understand that you have the responsibility to
configure all the passwords and other security settings
about the device, and keep your user name and password.
Maintenance
If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor)
require regular replacement. The average lifespan varies,
so periodic checking is recommended. Contact your
dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and
outside surfaces of the product cover. Do not use alkaline
detergents.
Using Environment
When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may
burn out.
To avoid heat accumulation, good ventilation is required
for a proper operating environment.
Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the
requirement of the device. Refer to product datasheet for
detailed information.
DO NOT expose the device to extremely hot, cold, dusty,
corrosive, saline-alkali, or damp environments. For
temperature and humidity requirements, see device
specification.
22