Technical Details - Franke PIN 530 Manual De Uso Y Mantenimiento

Encimeras encastrables
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

TECHNICAL DETAILS

MODÈLS
Induction plate 1400W
Induction plate 2300W
Max power W
1.
Installation (Fig 1)
Installation is the buyer's responsibility. The manufacturer accepts no liability for this service. Any action that the
manufacturer has to take due to an erroneous installation will not be covered by the guarantee.
The flush-mounted cook tops are designed for installation in work tops made of all kinds of material, providing they can
withstand a temperature of 100°C, and are between 30 and 40 mm thick. If the cook top is installed in a position so that
the side of a kitchen unit comes up against its left-hand or right-hand side, the distance between the vertical panel and
the edge of the cook top must always be at least 150 mm. The distance between the back wall and the edge of the cook
top must be at least 55 mm. A partition made of insulating material (wood or the like) must be inserted between the cook
top and the space below. This partition must be at least 17mm from the underside of the cook top tray.
Ventilation outlet: on the front side a free gap of at least 5mm have to be provided between the worktop and the
front part of the furniture (or the oven).
Fixing the cook top to the unit (Fig 2)
The cook top is fixed to the unit by means of the brackets and accessories provided. Holes are provided in the bottom of
the tray so that you can attach the screws (C) that hold the brackets (B) in place.
Applying the seal (Fig 3)
Important - The figure shows how the seal must be attached all around the perimeter.
This cook top has been designed for non-professional, domestic use.
2.
Electric connections (Fig 4)
Check the details given on the nameplate situated on the underside of the cook top, then make sure that the rated mains
voltage and power available are suitable for its operation.
Before making the electric connections, check the efficiency of the earthing system. Earthing of the cook top is
compulsory by law. The manufacturer will accept no liability for any personal injury or damage to property deriving from
failure to comply with this requirement.
For models without a plug, fit a standard plug capable of withstanding the specified load on the power cord. The cord's
earthing conductor is colored yellow and green. The plug must be accessible after the installation.
If you make a fixed connection to the mains, insert an all-pole circuit breaker between the cooktop and the mains. This
device shall have a contact separation in all poles, providing full disconnection under overvoltage category III conditions.
To connect the cook top power cord, loosen and remove the cover on the terminal block in order to access the contacts
inside. Make the connection, blocking the cord in place with the cable clamp provided and then close the terminal block
cover again immediately.
If you have to change the cord, the earthing (yellow / green) conductor must always be 10 mm longer than the line
conductors.
Use only rubber cable type H05RR-F.
DECLARATION OF CONFORMITY. In the parts destined to come into contact with foodstuffs, this appliance is in
accordance with the requirements of the EC directive 89/109 transposed in the Italian Legislative Decree N° 108 of
25/01/92.
CE Appliance conforming to the European directives 89/336/EEC, 93/68/EEC, 73/23/EEC and subsequent revisions.
INSTRUCTIONS FOR USE
Important: Before cooking with the appliance for the first time, it is important to clean the cook top.
The induction cooking method rapidly transfers the energy needed for cooking directly to the pan, so the cook top surface
remains cold but the pan heats up. The result is a fast, cost-effective and accurate cooking method.
This type of cook top can be used with enameled steel or stainless steel pans; it is not suitable for use with
glass, ceramic or aluminum pans (unless a special magnetic base plate is used).
Any pan with a bottom that is not perfectly flat is unsuitable and may damage the cook top.
Voltage
Current
PIN320
PIN530
230V
230V
17 A
22,5 A
1
2
1
1
3700
5100
- 9 -

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pin 320

Tabla de contenido