Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS
C-STRIP-B-LIN Series
8' FIXTURE INSTALLATION- HOOK AND CHAIN
(Requires use of (2) C-STRIP-A-SK Accessory)
1.
Detach the LED assembly by starting at one end of the first
4' section and pressing each side of the base. Pull the LED
assembly away from the base. Continue this along the entire 4'
section until the base and LED assembly are separated. See
Figure 4. Repeat for second 4' section.
2.
After separating the bases and LED assemblies, disconnect the
quick connects attaching the bases to the LED assemblies. Set
the LED assemblies aside until the base is mounted and wired.
See Figure 5.
3.
Insert the connecting bracket into one of the bases at the end with
no end plate. See Figure 12.
4.
Connect the two fixtures bases together using the (4) latches on
the connector plate. See Figure 13.
5.
Attach one supplied support chain to each supplied S-hook. To
prevent the connection from disengaging, use a pliers to crimp
closed the ends of the S-hooks inserted through chains. See
Figure 10.
6.
Attach the opposite ends of support chains to moulting surface
using customer supplied hardware. Mounting locations for the 4
chains should be directly above the 4 keyhole slots on the back of
the fixture base. Adjust chain lengths to allow proper suspension
of fixture. Make sure mounting surface and hardware can support
the weight of the fixture.
7.
Attach S-hooks to fixture base by routing S-hooks through keyhole
slots and out through holes next to slots. To prevent the fixture
from falling use a pliers to crimp closed the ends of the S-hooks
inserted into the base. See Figure 11.
8.
Remove the appropriate knockout from the base of the fixture and
route supply conduit or cord to knockout location. Attach conduit or
cord at knockout.
9.
With the fixture base installed, make wiring connections per the
appropriate wiring diagram in the Electrical Connections section.
NOTE: If using the occupancy sensor accessory, please refer
to OCCUPANCY SENSOR ACCESSORY section for installation
and programming of occupancy sensor before proceeding to the
Electrical Connections section.
10. Select desired wattage and CCT. See Figure 7.
11. Reconnect both quick connects that were disconnected in Step 2.
See Figure 8.
12. Reattach the (2) LED assemblies to the (2) fixture bases. The LED
assemblies should :"click" into place. See Figure 15.
13. Supply power to fixture.
OCCUPANCY SENSOR ACCESSORY
(Requires use of C-ACC-MW-L Accessory)
NOTE: When the occupancy sensor is used, dimming is controlled
by the occupancy sensor.
1.
Remove one 1/2" knockout on one end of the base.
2.
Mount the sensor to the base by passing the sensor wires and
threaded nipple through the 1/2" knockout opening. Secure the
sensor in place using the conduit nut on the nipple inside the
fixture base.
3.
Refer to instructions included with sensor for setting dip switches
to program sensor
http://lighting.cree.com/warranty
Document:
LPN00625X0001A1
Created By:
TMT
EMERGENCY DRIVER CHECK
(For Luminaires Equipped With Emergency
NOTE: Emergency driver and AC driver must be fed from the same
branch circuit.
NOTE: For short-term testing of the emergency function, the battery
must be charged for at least one hour. The emergency driver must be
charged for at least 24 hours before conducting a long-term test.
STEP 1:
When AC power is applied, the charging indicator light is illuminated,
indicating the battery is being charged. When power fails, the
emergency driver automatically switches to emergency power, operating
the LED array. When AC power is restored, the emergency driver
returns to the charging mode.
STEP 2:
Although no routine maintenance is required to keep the emergency
driver functional, it should be checked periodically to ensure that it is
working. The following schedule is recommended:
• Visually inspect the charging indicator light monthly. It should be
illuminated.
• Test the emergency operation of the fixture at 30-day intervals for
a minimum of 30 seconds. When the test switch is depressed, the
LED array should operate.
• Conduct a 90-minute discharge test once a year. The LED array
should operate for at least 90 minutes.
If the fixture fails any of these checks, consult service personnel.
EM Test Button Status Light Indicator
• Charging - red light on
• EM discharging - red light off
• EM damaged - red light off/red light flashing/fixture flashing
• Test switch button pressed - red light off
REFER ANY SERVICING INDICATED BY THESE CHECKS TO
QUALIFIED PERSONNEL
EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE
SAME BRANCH CIRCUIT.
FCC NOTICE
CAUTION: Changes or modifications not expressly approved could
void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAN ICES-005 (A)/NMB-005 (A)
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
|
866.924.3645
Date:
07-17-2021
Driver)
Publicidad
