Publicidad
Idiomas disponibles
Idiomas disponibles
Power/LED Connections
The Antec power supply is an ATX12V form factor power supply. An ATX12V power
supply has a single 20-pin Main Power Connector, a 6-pin AUX Power Connector, and a
4-pin +12V Power Connector for the motherboard. It also comes with five to seven 4-pin
Peripheral Power Connectors and one to two 4-pin Floppy Drive Power Connectors for
your drives. It is backwards compatible to previous ATX form factor power supplies. If
your motherboard does not support the AUX Power Connector or the +12V Power
Connector, you can still use this power supply.
The power supply is also equipped with a 3-pin fan signal connector. Connect it to one of
the fan connectors on your motherboard. You may monitor the speed of the power supply
rear fan through your motherboard BIOS or through the monitoring software that comes
with your motherboard. NOTE: The speed of the fan may be as low as 1500 RPM when
temperatures are low. At these speeds some motherboards may not be able to properly
detect the fan speed and may generate false warnings of fan failure. Please refer to your
motherboard manual for proper fan monitoring set up.
1.
Connect the 20-pin ATX power connector (and AUX or +12V connectors if
appropriate) to your motherboard.
2.
Reset (labeled RESET SW) connects to your motherboard at the RST connector. The
label should be facing the front of the case, and for all of the following connectors as
well.
3.
Power LED (labeled POWER LED) connector is located behind the Reset connector.
4.
Power Switch (labeled POWER SW) connects to the PWR connector on the
motherboard.
5.
Speaker (labeled SPEAKER) connector is behind the PWR connector.
6.
Hard Drive LED (labeled H.D.D. LED) connects to the IDE connector.
7.
LED I, LED II connectors: This case comes with two extra LED marked LED I,
LED II. You may use these LED for various purposes such as SCSI LED, Message
LED (blinks when your modem received fax or mail), etc.
USB Connection
There are 8 wires with connectors coming from the front mounted USB ports of the case.
1.
Locate the internal USB header pins on your motherboard. They should consist of
10-pins in two rows. NOTE: On some motherboards one or two pins may be marked
as NC. This indicates no contact. It is an empty pin. You don't need to use it. On
some motherboards one pin may be missing on either one or both rows. Don't worry
about it. You only need 8 pins to connect to.
2.
Consult your motherboard manual to get each of the pin-out positions.
3.
Power Pins: There are two power pins, one on each row. They are usually marked as
Power, Vcc or +5V. Connect the two +5V connectors to the two power pins. Each
connector can go to either pin.
4.
Ground Pins: There are two ground pins, one on each row. They are usually marked
as GROUND or GND. Connect the two GROUND connectors to the two ground pins.
Each connector can go to either pin.
Note: On some motherboards, there may be two ground pins on one row. You don't
need to use all of them. Make sure to connect one ground pin on each row.
5.
Data Pins: There are two plus data pins, one on each row, and two minus data pins,
one on each row. They are usually marked as USBD2+, USBD3+ and USBD2-,
USBD3- or USBP2+, USBP3+ and USBP2-, USBP3- respectively.
a. Connect the 1 +D connector to any of the two plus data pins. It can go to either
of the plus pins.
b. Connect the 1 -D connector to the minus data pin in the same row as the plus data
pin that 1 +D connector has just connected to.
c. Repeat the same procedures to connect the 2 +D and 2 -D to the motherboard.
Make sure they are in the same row.
All manuals and user guides at all-guides.com
2
IEEE1394 (FireWire, I-Link) Connection
There are six wires with connectors coming from the front mounted IEEE1394 port of your
case. They consist of 2 sets of twisted pair cables: TPA (Twisted Pair A) and TPB (Twisted
Pair B), a power cable (VP), and a ground cable (VG).
1.
Locate and identify the pin-out of the IEEE1394 port on your motherboard.
2.
Power Pin: Connect the VP connector to it.
3.
Ground Pin: Connect the VG connector to it.
4.
Data Pins: There are two sets of data pins. Each set consists of a plus and a minus
pin. They are usually marked as TPA+ and TPA-, TPB+ and TPB-.
a. Connect the TPA+ connector to the TPA+ data pin and TPA- connector to the
TPA- data pin.
b. Connect the TPB+ connector to the TPB+ data pin and TPB- connector to the
TPB- data pin.
3.5" Device Installation
1.
On the sides of the front bezel there are two tabs. Press the tabs to remove the top
half of the bezel.
Note: You can see the external drive bays now. There are three 5.25"drive bays and
one 3.5" drive bay assembly which can hold two 3.5" devices.
2.
Unscrew the two silver thumbscrews located on the bottom of the drive bay assembly
and slide out the 3.5" drive bay assembly.
3.
Install your floppy drive into the bottom drive bay. Mount the other 3.5" device into
the top drive bay.
4.
Slide the whole assembly back into the case and fasten it with the thumbscrews.
Inside the case, there is an internal 3.5" drive cage. It can hold three 3.5" devices.
5.
Pull the quick release lever towards the rear of the case and release the cage. Put the
cage on a flat surface.
Note: If you want to have a cooling fan in the drive cage, you should install the fan
before installing the drives.
6.
Mount your other 3.5" devices into the drive cage.
7.
Slide and lock the drive cage back into the case.
8.
Find a small 4-pin white connector on the power supply and connect it to the male
4-pin connector on the floppy drive.
9.
Connect a large 4-pin white connector from the power supply to the male 4-pin
connector on each of the other devices.
5.25" Device Installation
1.
There are three metal plates covering the 5.25" drive bays.
2.
Carefully use your hands to twist the metal plate back and forth until it breaks off.
Note: Don't break off the plates covering the drive bays that you are not using now.
Be careful of the newly exposed metal where the grills were attached as these areas
are likely to be sharp.
3.
Take two of the Drive Rails and mount them to the sides of the 5.25" device.
Make sure the metal portion is angled away from the device and facing forward.
4.
Slide the device into the drive bay until you hear a click.
5.
Mount the other devices accordingly.
6.
Connect a large 4-pin white connector from the power supply to the male 4-pin
connector on each of the devices. After you have finished the installation, carefully
use your thumbs to push the plastic drive bay covers off the bezel and attach the
bezel back into the case. Like the metal plates, take off only the covers for the drive
bays you are using now.
3
Publicidad
