Sound Values And Vibration Values; Bar And Chain Combinations; Spare Parts And Accessories - Stihl MSA 220.0 T Manual De Instrucciones

English
– Energy content in Wh: see rating label
– Weight in kg: see rating label
– Permissible temperature range for operation
and storage: + 10 °C to + 50 °C
®
– Bluetooth radio interface (only for batteries
with ):
– Data connection: Bluetooth
mobile appliance must be compatible with
®
Bluetooth Low Energy 5.0 and support
Generic Access Profile (GAP).
– Frequency band: ISM band 2.4 GHz
– Maximum RF power transmitted: 1 mW
– Signal range: approx. 10 m. The signal
strength depends on the ambient conditions
and the mobile terminal. Signal range can
vary greatly depending on local conditions,
including the receiver. The range may be
perceptibly reduced inside enclosed rooms
and through metal barriers (such as walls,
shelves or cases).
– Mobile appliance operating system require‐
ments: Android or iOS (current version or
higher)
21.5 Sound Values and Vibration
Values
STIHL recommends wearing ear defenders.
– Sound pressure level L
to EN ISO 22868: 94 dB(A) The K value for
the sound pressure level is 2 dB(A).

22 Bar and Chain Combinations

22.1 STIHL MSA 220.0 T, MSA 220.0 TC Chainsaw
Pitch Drive link
gauge/groove
width
3/8" P 1.3 mm
The cutting length of a guide bar depends on the chainsaw and the saw chain being used. The actual
cutting length of a guide bar may be less than the specified length.
1)
If this guide bar is used, the chainsaw may be used only with a STIHL AP battery inserted directly in
the saw.
23 Spare Parts and Accesso‐
ries
23.1

Spare parts and accessories

These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
52
®
5.1. The
measured according
pA
Length Guide bar
30 cm Rollomatic E /
Light 04
1)
35 cm
Rolloma‐
tic E Light /
1)
40 cm
Light P04
22 Bar and Chain Combinations
– Sound power level L
EN ISO 22868: 104 dB(A) K-value (uncer‐
tainty) for sound power level is 2 dB(A).
– Vibration level a measured according to EN
hv
ISO 22867
– Control handle: 3.4 m/s². The K value for
the vibration level is 2 m/s².
– Handlebar: 3.0 m/s². The K value for the
vibration level is 2 m/s².
The sound and vibration levels indicated were
measured according to a standardized test
method and can be used as a basis for compar‐
ing electric power tools. The sound and vibration
levels actually occurring may vary from the val‐
ues indicated, depending on the type of applica‐
tion. The sound and vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual sound and vibration stress has
to be estimated. The times when the electric
power tool is switched off and the times when it
is switched on but running under no load can be
taken into account in the estimate.
21.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Number of Number of
teeth, spro‐ drive links
cket nose
9
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
measured according to
wA
Saw chain
44
50 63 PM3 (3636)
63 PS3 (3616)
55
0458-007-9821-A