MSW Motor Technics MSW-DMS-VB Manual De Instrucciones página 4

EN
TECHNICAL DATA
Parameter description Parameter value
Product name VACUUM BASE
Model MSW-DMS-VB
Dimensions [Width
335x425x160
x Depth x Height; mm]
Weight [kg] 4,3
EU 12 mm pneumatic male
Connection type
connector (for quick coupler)
Maximum load [kg] 100
Working pressure
0,6-0,8 / 6-8
[MPa/Bar]
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed and
manufactured in accordance with strict technical guidelines,
using state-of-the-art technologies and components.
Additionally, it is produced in compliance with the most
stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
trouble-free operation, use it in accordance with this user
manual and regularly perform maintenance tasks. The
technical data and specifications in this user manual are
up to date. The manufacturer reserves the right to make
changes associated with quality improvement. The device
is designed to reduce noise emission risks to a minimum,
taking into account technological progress and noise
reduction opportunities.
LEGEND
Read instructions before use.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation. (general
warning sign)
Wear protective goggles.
ATTENTION! Hand crush hazard!
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details may
differ from the actual product.
The original operation manual is written in German. Other
language versions are translations from the German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury or even death.
The terms "device" or "product" are used in the warnings
and instructions to refer to VACUUM BASE.
6
U S E R M A N U A L
2.1. SAFETY IN THE WORKPLACE
a) Make sure the workplace is clean and well lit. A messy
or poorly lit workplace may lead to accidents. Try
to think ahead, observe what is going on and use
common sense when working with the device.
b) If you are unsure about whether the product is
operating correctly or if you find damage, please
contact the manufacturer's service centre.
c) Only the manufacturer's service centre may make
repairs to the product. Do not attempt to make repairs
yourself!
d) Children or unauthorised persons are forbidden to
enter a work station. (A distraction may result in loss
of control over the device).
e) Only connect and disconnect the pressure line when
the air valve is closed.
f) Do not point the pressure line towards yourself or
toward other people or animals.
g) Do not cut off the supply of compressed air by
crushing or bending pressure hoses.
h) When starting the device, increase the air supply
to the device gradually in order to ensure that it is
functioning properly. If you notice any abnormal
operation of the device, disconnect it immediately
from the compressed air and contact
manufacturer's service point.
i) Please keep this manual available for future reference.
If this device is passed on to a third party, the manual
must be passed on with it.
j) Keep packaging elements and small assembly parts in
a place not available to children.
k) Keep the device away from children and animals.
l) If this device is used together with another equipment,
the remaining instructions for use shall also be
followed.
2.2. PERSONAL SAFETY
a) Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b) The device can be handled only by physically fit
persons who are capable of handling it, properly
trained, familiar with this manual and trained within
the scope of occupational health and safety.
c) When working with the device, use common sense
and stay alert. Temporary loss of concentration while
using the device may lead to serious injuries.
d) Use personal protective equipment as required
for working with the device, specified in section 1
(Legend).
The use of correct and approved personal protective
equipment reduces the risk of injury.
e) Compressed air may cause serious injury.
f) The device is not a toy. Children must be supervised to
ensure that they do not play with the device.
Rev. 14.10.2020
2.3. SAFE DEVICE USE
a) Do not overload the device. Use the appropriate tools
for the given task. A correctly-selected device will
perform the task for which it was designed better and
in a safer manner.
b) Make sure the pressure line is disconnected before
attempting any adjustments, accessory replacements
or doing any work on the device. Such a preventive
measure reduces the risk of an accident.
c) When not in use, store in a safe place, away from
children and people not familiar with the device who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
d) Keep the device in perfect technical condition. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
e) Keep the device out of the reach of children.
f) Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
g) When transporting and handling the device between
the
the warehouse and the destination, observe the
occupational health and safety principles for manual
transport operations which apply in the country
where the device will be used.
h) Do not move, adjust or rotate the device in the course
of work.
i) Do not leave this appliance unattended while it is in
use.
j) Clean the device regularly to prevent stubborn grime
from accumulating.
k) At locations where there is a high risk of mechanical
damage, use a reinforced hose for compressed air
connections.
l) Before each use ensure the nozzle is correctly installed
in the device and that the hose is correctly attached
and undamaged.
m) Do not carry or hang the device by the pressure line.
n) Do not touch any moving parts or accessories
unless the device has been disconnected from the
compressed air supply.
o) If you notice a leak from the device or hoses,
immediately disconnect the compressed air supply
and resolve the defects.
p) Do not exceed the recommended supply pressure as
this may damage the device.
q) The device is not a toy. Cleaning and maintenance may
not be carried out by children without supervision by
an adult person.
r) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
s) Keep the device away from sources of fire and heat.
t) Do not overload the device.
u) Do not exceed the maximum permissible operating
pressure!
Rev. 14.10.2020
EN
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The product is intended for the vacuum mounting of a
drilling machine stand.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
1
2
6
4
3
5
1. Stabilizing bolts (x4)
2. Tripod mounting anchor
3. Holder (x2)
4. Male pneumatic connector (suction)
5. Air supply relief valve
6. Rubber gasket (underneath - not visible in the picture)
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The ambient temperature must not exceed 45°C and the
relative humidity should not exceed 85%. Keep the device
away from any hot surfaces. The device should always be
used on an even, stable, fireproof and dry surface, out of
reach of children and people with impaired psychological,
sensory and mental functions. The valve that disables the
compressed air supply should be immediately accessible
from the area where the device is being used. Make sure
that the pressure of the air supplying the device does not
exceed the recommended range.
ASSEMBLING THE APPLIANCE
A vacuum pump with a pneumatic hose (not included in the
set) is required for the operation of the device. Mount the
drill stand with the provided anchor on the mounting base
plate. Connect a hose from the vacuum pump to the male
connector of the pneumatic quick coupler. Position the base
plate on the surface to be drilled.
3.3. DEVICE USE
Use a vacuum pump to create a vacuum (the pressure should
be within the specified operating range - see parameter
tables) so that the base adheres tightly to the substrate.
Stabilize the position of the base and the tripod using the
stabilizing bolts located at the ends of the base and tighten
the nuts on them well. At all times during this procedure, the
mounting should be connected to a running pump to ensure
secure mounting and safe operation.
7