Cleaning And Storage; Noise Development; Technical Data - Clatronic BS 1273 Instrucciones De Servicio/Garantía

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
Ill. 4
Ill. 5
Important note!
Cleaning may become necessary after a shorter time, depen-
ding on the conditions of use, e.g. when vacuuming fi ne dust.
If the suction power of your vacuum cleaner diminishes please
clean the fi lters as described.
If the suction power suddenly diminishes during operation this
may be due to the fi lters being locked.
34
05-BS 1273.indd 34
05-BS 1273.indd 34
Every third time the dust container
is emptied, or in the case of severe
soiling, clean the fi lter by allowing
water to fl ow through the fi lter fabric
against the direction in which the
vacuum cleaner blows. The dust
container should only be reinserted
when it is completely dry!
Now place this back in position
once it has completely dried!
Caution: Never wash the fi lter
in the washing machine, and
please do not use a hairdryer
to dry it.
2. Inlet fi lter
The inlet fi lter is to be found in
the dust fi lter compartment - see
the arrow. Press the button to
release the dust container and then
remove it. Pull the fi lter out towards
the front. Clean the inlet fi lter
approximately every tenth time the
dust container is emptied, or more
frequently if necessary. Please
ensure that the fi lter is always
clean, as otherwise air circu-
lation cannot be guaranteed. If
necessary, the fi lter can also be
washed in warm water without any
additives. Place it back into place
only once it is completely dry!
3. Outlet fi lter
The appliance is also equipped
with an outlet fi lter. In order to en-
sure that the fi lter works correctly,
we recommend that you replace
it every six months. It is located
on the rear part of your appliance
behind a ventilation grid. Open
the ventilation grille by pressing
the lever on its side. Then pull the
grille out towards the front. Remove
the fi lter and clean as described
above. Fit the fi lter back into place
and close the ventilation grid by
following the steps above in the
opposite order.

Cleaning and storage

Cleaning
Pull the plug out of the socket before cleaning!
Clean the casing with a dry cloth.
Clean the motor protection fi lter approximately every 3.
time the vacuum cleaner is emptied. Clean the fi lter in hot
water without additives. Put it back into place only once it is
completely dry.
Storage
Let the iron cool down completely.
Wind the cable completely.
Please position the device horizontally and insert the hook
on the telescopic tube into the parking aid (7) on the back of
the device.
Troubleshooting
The Device Does Not Work.
Remedy:
Check the connection to the mains.
Check the position of the switch.
The device does not suck up anything.
Possible Cause:
The dust container or the fi lters are dirty.
Remedy:
Empty or clean the components.
Possible Cause:
There is a foreign body in the suction tube or the nozzle.
Remedy:
Check the accessories for foreign bodies.

Noise development

The sound pressure level in the ear of an operator (LpA) was
measured according to DIN EN ISO 3744.
Sound pressure level detected: 78.0 dB(A) (no limit)

Technical Data

Model: ...............................................................................BS 1273
Power supply: ................................................220-240 V, 50/60 Hz
Power consumption:
P
: ............................................................................ 1800 W
nom.
P
: ............................................................................2300 W
max.
Protection class: .......................................................................... ΙΙ
Net weight: .........................................................................5.85 kg
07.03.2008 8:24:46 Uhr
07.03.2008 8:24:46 Uhr

Publicidad

Tabla de contenido
loading

Tabla de contenido