Assembly And Adjustments - Black and Decker BEHB101 Traducido De Las Instrucciones Originales

IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn appliance off and disconnect
appliance from power source before making any
adjustments or removing/installing attachments
or accessories. An accidental start‑up can
cause injury.
Installing Cord (Fig. B)
1. Place the cocktail maker upright on a flat, level,
stable surface.
2. Insert the jack plug 1
3. Plug the other end of the cord into an outlet.
Installing Coaster (Fig. C)
1. Place the drip tray cover into the drip tray
rounded and slanted corners of the cover line up with
the rounded and slanted corners of the drip tray.
2. Ensure the cover sits fully inside the drip tray.
3. To remove the cover, lift from the drip tray cover
finger hole 5 .
Installing Bottles (Fig. D)

WARNING: Only use water in the supplied water
bottle. Use of other liquids or substances in the water
bottle may result in damage to the appliance.

CAUTION: Avoid spills while installing bottles.
nOTE: It is recommended to use 750 ml bottles or smaller
to ensure all bottles sit on the bottle platform
hanging off the platform.
nOTE: Bottles must fit between the bottle platform and the
top of the cocktail maker while standing.
1. Slide a straw 7 into a bottle so the straw tip
bottom of the bottle.
2. Slide the bottle stopper
fully in the top of the bottle.
3. Ensure the straw lock
4. Align the straw plug notch
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
of the cord into the plug port
3 so the
6 without
9 sits on the
down the straw until it sits
13
8 is up.
12 with the straw slot
5. Slide the straw plug
allowing the bottle to sit freely in its designated space.
Ensure the straw plug is fully seated in the slot
6. To lock it into place, push the straw lock down until it
clicks. Ensure the lever is fully down.
7. Repeat for all bottles.
iMPORTAnT: Bottles must be placed in their designated space
to ensure the correct drink is dispensed. Names of the liquids are
located in each spot, indicating the appropriate liquid.
iMPORTAnT: The following are the only liquids that should
be used with the appliance.
• Water
• Gin
• Rum
• Vodka
• Tequila
• Whiskey
Removing Bottles (Fig. E)

CAUTION: Avoid spills while removing bottles.
1. Lift the straw lock
2. Slide the straw plug
3. Pull the bottle stopper
the straw 7
nOTE: If the cocktail maker pauses for an empty bottle and you
press mix without replacing the bottle, it will skip to the next
bottle in the recipe. If that bottle is empty, it will pause again.
Refer to the PAUSE MODE section for more information.
2 .
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
On/Off (Fig. F)

WARNING: Do not interact with the cocktail maker
while it is operating.
• To turn the cocktail maker on, push the "I" side of the power
switch 14
will blink. When they become solid, the cocktail maker is
ready to use.
• To turn the cocktail maker off, push the "O" side the side of
the power switch. All LEDs will turn off.
Choose a Glass Tray (Fig. G)
Place a glass or shaker on either the glass shelf
tray 3 , depending on the height of the glass being used.
Refer to the cocktail image on the capsule
nOTE: A glass or shaker must be in place before making a
drink to avoid spillage.
short glass:
1. Pull the glass shelf down so it stands straight out from
the tower
2. Place a small glass on the glass shelf.
10 .
11 all the way into the straw slot,
8 .
11 and bottle off the cocktail maker.
13 out of the bottle and remove
.
. The 4 strength LEDs 15 and 6 bottle LEDs
18 .
English
16
17 or drip
20 for glass style.
5