Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
on the label. If you see this bad battery blink pattern, do not
continue to charge the battery. Return it to a service center
or a collection site for recycling.
hot/Cold pack delay
When the charger detects a battery that is
excessively hot or excessively cold, it
automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery has
normalized. After this happens, the charger
automatically switches to the Pack Charging
mode. This feature ensures maximum battery
life. The light flashes in the pattern indicated on
the label.
problem power line
When the charger is used with some portable
power sources such generators or sources that
convert DC to AC, the charger may temporarily
suspend operation. The LED flashes in the
pattern indicated on the label. This indicates
that the power source is out of limits.
leaving the battery in the charger
The charger and battery pack can be left connected with the
green LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.
Important charging notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). Do not charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or
other appliance.
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights.
c. Move charger and battery pack to a location where
the surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. Do not continue to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
28
5. Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power
supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
WARNING! Shock hazard. Do not allow any liquid to
get inside charger. Never attempt to open the battery
pack for any reason. If the plastic housing of the
battery pack breaks or cracks, return to a service center
for recycling.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Attaching the Transparent Filter with
Quick Connect (Fig. C)
This pressure cleaner must be used with the quick connect
adapters. The garden or suction hose can only be attached
when the transparent filter
1. To connect the transparent filter
connect end to the pressure cleaner, place the end of the
transparent filter
3
onto the water intake
the transparent filter
NoTE: Avoid cross threading when installing the
transparent filter. Cross threading will cause leaks.
To Attach the Spray Wand (Fig. D)
The spray wand connect to the pressure cleaner. To connect
the spray wand
to the pressure cleaner.
9
•
Insert the end of the attachment into the opening on
the pressure cleaner
2
clockwise until its secured into working position.
•
To remove the attachment, push in and turn the
attachment counterclockwise and pull from the pressure
cleaner
.
2
To Attach the Garden or Suction Hose
(Fig. E, F, G)
Connecting the garden hose or suction hose will depend on
the job to be performed.
To Attach Garden Hose (Fig. E, F)
This pressure cleaner must be used with the quick
connect adapters.
1. To connect the quick connect hose adapter
a garden hose, thread the quick connect hose adapter
onto the end of the garden hose. Tighten the garden
hose by hand.
NoTE: Avoid cross threading when installing the hose.
is installed.
3
3
with its quick
15
3
onto the water intake
. Push in and turn the attachment
8
and screw
15
.
to
Publicidad
Tabla de contenido
