Fcc Caution - Canon imageRUNNER ADVANCE DX 4845i Instrucciones De Seguridad Importantes

FCC (Federal Communications
Commission) Users in the U.S.A.
Multi Function Printer, Model F810300
Contains Transmitter Module FCC ID: AZDK30365
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.

FCC CAUTION

Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
[NOTE]
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate, radio
frequency energy and, if not installed and used in
accordance with the Operator's Manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own
expense.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure Guidelines
as this equipment has very low levels of RF energy. But it
is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from
person's body.
Use of shielded cables are required to comply with Class
A limits in Subpart B of Part 15 of the FCC Rules.
Do not make any changes or modifications to the
equipment unless otherwise specified in the manual. If
you make such changes or modifications, you could be
required to stop operation of the equipment.
CANON U.S.A., INC
One Canon Park, Melville, NY 11747, U.S.A.
TEL No. 1-800-OK-CANON
Wireless LAN Regulatory Information
Regulatory information for users in Brazil
Para consultas, visite: www.anatel.gov.br
Este equipamento possui um módulo de
radiação restrita homologado na Anatel sob o
número 04082-14-09033
MODELO: K30365
04082-14-09033
Resolução 680:
Este equipamento não tem direito à proteção contra
interferência prejudicial e não pode causar interferência
em sistemas devidamente autorizados.
Regulatory information for users in Canada
English This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's
licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
This equipment complies with ISED radiation exposure
limits set forth for an uncontrolled environment and
meets RSS-102 of the ISED radio frequency (RF) Exposure
rules as this equipment has very low levels of RF energy.
But it is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from
person's body.
Français [ French ] L'émetteur/récepteur exempt de
licence contenu dans le présent appareil est conforme
aux CNR d'Innovation, Sciences et Développement
économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition
aux rayonnements énoncées pour un environnement
non contrôlé et respecte les règles d'exposition aux
fréquences radioélectriques (RF) CNR-102 de l'ISDE
puisque cet appareil a une niveau tres bas d'energie RF.
Cependant, il est souhaitable qu'il devrait être installé et
utilisé en gardant une distance de 20 cm ou plus entre
le radiateur et le corps humain.
Regulatory information for users in Mexico
Módulo WLAN instalado adentro de este producto
IFETEL RCPCAK314-1933
CANON INC.
K30365
La operación de este equipo está sujeta a las siguientes
dos condiciones:
(1) es posible que este equipo o dispositivo no cause
interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier
interferencia, incluyendo la que pueda causar su
operación no deseada.
Regulatory information for users in Uruguay
imageRUNNER ADVANCE DX 4845i/4835i/4825i contains
URSEC approved Wireless LAN Module (Model name:
K30365 or FM1M948).
The following applies in California, USA only:
The battery included with your product contains
perchlorate material and may require special handling.
See http://www.dtsc.ca.gov/hazardouswaste/
perchlorate/ for details.
Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile
Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine.
See "Specifications" in the User's Guide for specific
dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary) should
be used. If the Super G3 2nd Line Fax Board is
installed, a multi telephone line (touch-tone or
3
rotary) can be used.
2. Order an RJ11-C telephone wall jack (USOC), which
should be installed by the telephone company. If the
RJ11-C wall jack is not present, telephone/facsimile
operation is not possible.
3. Order a normal business line from your telephone
company's business representative. The line should
be a regular voice grade line or an equivalent one.
Use one line per unit. If the Super G3 2nd Line Fax
Board is installed, you can use a multi-line.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you
communicate overseas
[NOTE]
Canon recommends an individual line following industry
standards, i.e.,2,500 (touch-tone) or 500 (rotary/pulse
dial) telephones. A dedicated extension off a PBX (Private
Branch eXchange) unit without "Call Waiting" can be
used with your facsimile unit. Key telephone systems are
not recommended because they send nonstandard
signals to individual telephones for ringing and special
codes, which may cause a facsimile error.
C. Power Requirements
The machine should be connected to a standard 120
volt AC, three-wire grounded outlet only.
Do not connect this machine to an outlet or power line
shared with other appliances that cause "electrical noise. "
Air conditioners, electric typewriters, copiers, and
machines of this sort generate electrical noise that often
interferes with communications equipment and the
sending and receiving of documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the
[insert location of the label] of this equipment is a label
that contains, among other information, a product
identifier in the format US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone
company.
The REN is used to determine the number of devices
that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not
all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be
connected to a line, as determined by the total RENs,
contact the local telephone company.
For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the
format US:AAAEQ##TXXXX. The digits represented by ##
are the REN without a decimal point (e.g., 03 is a REN of
0.3).
An FCC compliant telephone line cable and modular
plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or
premise wiring using a compatible modular jack that is
Part 68 compliant.
This equipment may not be used on coin service
provided by the telephone company. Connection to
party lines is subjected to state tariffs.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be
corrected by the procedures described in the User's
Guide, disconnect the equipment from the telephone
line cable and disconnect the power cord. The
telephone line cable should not be reconnected or the
power switch turned ON until the problem is completely
En En
Es Es