Remote Control Unit - Denon AVR-1602 Instrucciones De Operación

11 REMOTE CONTROL UNIT

Operating DENON audio components
DENON remote-controllable audio components can be controlled using this
unit's remote control unit. Note that some components, however, cannot be
operated with this remote control unit.
CD MD/CDR
1
AUDIO VIDEO
POWER
1
AVR/AVC TV VCR DVD/VDP Set the slide switch to the position for the
ON
CD DVD/VDP component to be operated (CD or MD/CDR).
OFF 1 2 3
V. AUX VCR TV/DBS
4 5 6 7
2-c 2
INPUT MODE CDR / TAPE TUNER SHIFT Use the buttons shown below to operate the audio component.
8 9 0
SURROUND
For details, refer to the respective component's manual.
MODE TAPE·VCR
6 7
CHANNEL
0
2-b
a. For CD player and MD/CD recorder
3 2 0
VIDE SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE VIDEO SELECT CD·MD/CDR·DVD/VDP
8 3 9
2-a
TITLE
2
6 7
8
SYSTEM SURROUND
SET UP MENU MASTER
6
CH SELECT VOL
SELECT SYSTEM
T.TONE STATUS MUTING
RETURN DISPLAY
CHANNEL TV VOLUME
B
REMOTE CONTROL UNIT RC-896
b. For tape deck (TAPE)
V. AUX VCR
4
INPUT MODE CDR / TAPE
8
SURROUND
MODE
0
3
c. For TUNER
V. AUX VCR
4
INPUT MODE CDR / TAPE
8
SURROUND
MODE
0
3
NOTE:
• Tape deck (TAPE) and tuner can be operated when the switch is at "AUDIO" position.
Preset memory (Audio component)
DENON components can be operated by setting the preset memory for MD or
CDR. Operation is not possible for some models.
CD MD/CDR
1
1
AUDIO Set the slide switch to "MD/CDR".
VIDEO
POWER
AVR/AVC DVD/VDP
TV VCR
ON
CD DVD/VDP
1 2 3
OFF
V. AUX VCR TV/DBS
2
4 5 6 7 Holding in the PLAY (1) button, press the
INPUT MODE CDR / TAPE TUNER SHIFT
8 9 0 button for the components you want to set.
SURROUND
·
MODE TAPE VCR
(Refer to table 1.)
6 7
CHANNEL
0
3 2 0
Table 1: Combinations of Personal System
2
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
8 3 9
2
6 7
SYSTEM SURROUND
2
SET UP MENU MASTER
CH SELECT PLAY (1)
VOL
SELECT
T.TONE STATUS MUTING
NOTE:
RETURN DISPLAY
• The memory can only be preset for either the MD or the CDR.
CHANNEL TV VOLUME
B
REMOTE CONTROL UNIT RC-896
reset.
All manuals and user guides at all-guides.com
CD
AUDIO
, : Manual search
6 7
DISC SKIP+
(reverse and forward)
: Stop
2
3 9
: Play
1
2
7
, : Auto search
8 9
SURROUND
: Pause
3
DISC : Switch discs
SKIP+ (for CD changers only)
: Rewind
6
TV/DBS
5 6 7
: Fast-forward
7
TUNER SHIFT
: Stop
9 0 2
: Forward play
TAPE · VCR 1
6 7
: Reverse play
0
CHANNEL
2 0
SHIFT : Switch preset channel range
TV/DBS
5 6 7
CHANNEL : Preset channel
TUNER SHIFT
(+, –) (up/down)
9 0
TAPE · VCR
6 7
CHANNEL
2 0
CD
AUDIO
Codes
MASTER
VOL.
MASTER
VOL.
MD CD-R
Preset codes set upon shipment from the factory and when
Preset memory (Video component)
DENON and other makes of components can be operated by setting the preset memory for your make of video
component.
This remote control unit can be used to operate components of other manufacturers without using the learning
function by registering the manufacturer of the component as shown on the List of Preset Codes (page 164).
Operation is not possible for some models.
MD/CDR
1
VIDEO
CD MD/CDR
1
AUDIO VIDEO
POWER
AVR/AVC TV VCR DVD/VDP
2
ON
CD DVD/VDP
OFF 1 2 3
2
3
V. AUX VCR TV/DBS
4 5 6 7
INPUT MODE CDR / TAPE TUNER SHIFT
2, 3
8 9 0
SURROUND
TAPE VCR ·
MODE
6 7
CHANNEL
0
3 2 0
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
3
8 9
2
6 7
3
SYSTEM SURROUND
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
CHANNEL TV VOLUME
B
REMOTE CONTROL UNIT RC-896
4
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation,
cover the remote control unit's transmitting window while setting the preset memory.
• Some models and years of manufacture of components of the manufacturers listed on the List of Preset
Codes cannot be used.
• The unit is equipped with several types of remote control codes which depend on the manufacturer. If there
is no operation, please change the preset code (a 2-digit number) and try again.
MD/CDR
VIDEO
Set the slide switch to "VIDEO".
Holding in the SHIFT button q, press the POWER
button w of the components (DVD/VDP, VCR or
TV) you want to set.
Press and hold in the SHIFT button.
Holding in the SHIFT button q, press the number
buttons w to input the preset code (consisting of
2-digit numbers) for the manufacturer of the
component whose signals you want to store in
the memory.
See the list on page 164 for the preset codes
(consisting of 2-digit numbers).
To continue registering other components, repeat steps 2 to 3.
ENGLISH
CD MD/CDR
AUDIO VIDEO
w
q
w
q
11