Ryobi RLM3313A Manual Del Usuario página 181

■ Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
■ Before use and after any impact, check that there are
no damaged parts. A defective switch or any part that
is damaged or worn should be properly repaired or
replaced by an authorised service centre.
■ Make sure the cutting attachment is properly installed
and securely fastened.
■ Never operate the product unless all guards, deflectors,
and handles are properly and securely attached.
■ Consider the environment in which you are working.
Keep the working area free from wires, sticks, stones
and debris that if struck by the cutter, can become
thrown objects.
LAWN TRIMMER / EDGE TRIMMER SAFETY
WARNINGS
■ Use the product in daylight or with good artificial light.
■ Avoid using on wet grass.
■ Do not walk backwards when using the product.
■ Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance. Always be
sure of your footing on slopes. Walk, never run.
■ Keep bystanders, children and pets 15 m away from
the area of operation. Stop the product if anyone enters
the area.
■ Keep the cutting attachment below waist level.
■ Never operate the product with damaged guards or
without guards in place.
■ Never fit a metal replacement line.
■ Keep hands and feet away from the cutting means at all
times, especially when switching on the motor.
■ Beware, the cutting elements continue to rotate after
the motor is switched off.
■ Beware of objects thrown by the cutting means. Clear
debris like small stones, gravel and other foreign
objects from the work area before starting operation.
Wires or string may become entangled with the cutting
means.
■ Switch off and disconnect from the power supply before:
● servicing
● leaving the product unattended
● cleaning your product or clearing a blockage
● changing accessories
● checking for any damage after hitting a foreign
object
● checking for any damage if the product starts to
vibrate abnormally
● performing maintenance
■ The small blade fitted to the lawn guard is designed to
trim the new extended line to the correct length for safe
and optimum performance. It is very sharp; do not touch
it, particularly when cleaning the product.
■ Always ensure that ventilation openings are kept clear
of debris.
■ Make sure the cutting head attachment is properly
installed and securely fastened.
2 | English
■ Make sure all guards, deflectors, and handles are
properly and securely attached.
■ Do not modify the product in any way. This may
increase the risk of injury to yourself or others.
■ Use only the manufacturer's replacement cutting line.
Do not use any other cutting attachment.
■ Immediately switch off and disconnect from the mains
in the event of accident or breakdown. Don't operate
the product again until it has been fully checked by an
authorised service centre.
TRANSPORTATION AND STORAGE
■ Stop the product and allow it to cool down before
storing or transporting. Always disconnect from the
power supply and wind the cable to prevent damage.
■ Clean all foreign materials from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents, such
as garden chemicals and de-icing salts. Do not store
outdoors.
■ For transportation in vehicles, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, poor performance, and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualifi ed service
technician. For service, bring the product to an
authorised service centre for repair. When servicing, use
only identical replacement parts.
■ Switch off and disconnect from the mains before
conducting any maintenance or cleaning work.
■ You may make adjustments and repairs described in
this manual. For other repairs, contact the authorised
service agent.
■ For the replacement line, use only nylon filament line
of the diameter described in the specification table of
this manual.
■ After extending the new cutter line, always return the
product to its normal operating position before starting.
■ After each use, clean the product with a soft dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
■ Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in a safe
working condition.