Publicidad
Idiomas disponibles
Idiomas disponibles
en
12
For your safety.
Do not use this machine before you have thor-
oughly read and completely understood theseop-
erating instructions, including the figures,
specifications, and safety regulations.
Please also observe the relevant national industrial safe-
tyregulations (e. g. in Germany: BGV A2, BGR 500).
Non-observance of the safety instructions in the said
documentation can lead to an electric shock, burns
and/or severe injuries.
This Instruction Manual should be kept for later use and
enclosed with the power tool, should it be passed on
or sold.
Read and observe the operating instructions of
the belt grinder GI75/GI150, which is to be
mounted to this machine.
For assembly of the cylindrical grinding device to the
belt grinder, use only the fastening material provided.
Faulty assembly can cause the cylindrical grinding device
to loosen from the belt grinder during operation and
lead to serious accidents.
Intended use of the machine.
The cylindrical grinding device GIC is to be used
together with the belt grinder GI75/GI150 exclusively
for grinding and polishing round steel pipes, light metal
pipes as well as solid round stock with diameters
D = 10–130 mm using the application tools and acces-
sories recommended by FEIN in weather-protected
environments.
The cooling unit GXW is intended for cooling of the
workpiece.
Special safety instructions.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.
While working, do not wear loose clothing, jewellery or
open, long hair. Despite protective devices, loose
objects can be snagged or caught by moving parts and
lead to injury.
Before switching on, make sure that no workpiece is
inserted in the cylindrical grinding device. The work-
piece can be thrown from the machine and cause seri-
ous accidents.
Never touch the running grinding belt. Danger of
injury.
In situations of danger, immediately press the safety
pushbutton. The machine runs on for approx. 50 sec-
onds.
Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
The mains plug of the machine may be mounted only by
a qualified electrician. The protective conductor in the
mains socket outlet must be connected with the pro-
tective earthing of the mains supply.
Pull out the mains plug for maintenance and repair!
Switching the machine on unintentionally can lead to
serious injuries.
Have the electrical safety of the machine checked reg-
ularly in accordance with statutory regulations. For
machines that have not been checked, there may be
danger of electrical shock!
Check the rotation direction of the motor before start-
ing the operation of the machine for the first time. If the
rotation direction of the motor is incorrect, the work-
piece can be thrown from the machine and cause an
accident. The rotation direction may be changed only
by a qualifiedelectrician.
Always work with great care and attention, especially
when inserting and removing the material. If your
attention fades, your hands may be seriously injured.
The surface being worked can become very hot. Do not
touch it with your hands.
Be careful when working short or thin material. When
inserting and removing, your hands may be caught by
the grinding belt or brake wheel, causing serious injury.
For longer pipes and round stock, we recommend the
using the pipe guide GXIS-1/GXIS-2.
Exercise caution after switching off. The machine runs
on for approx. 50 seconds. Carry out adjustments and
maintenance only when the grinding belt is stopped.
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Publicidad
