Publicidad
Idiomas disponibles
Idiomas disponibles
• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.
• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your
tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A
rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC
power. This information is printed on the nameplate. Lower voltage will cause loss of power
and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does
not operate, check the power supply.
Operating Instructions
WARNING: To reduce the risk of serious personal injury, read, understand and follow all
important safety warnings and instructions prior to using this tool.
SWITCH
To turn the tool ON, hold it as shown in Figure 1 and push the portion of the switch marked "I".
To turn the tool OFF, push the portion of the switch marked "O".
OPERATION
Grasp product as shown in Figure 1 and turn it on. Move it in long sweeping strokes across
the surface, letting it do the work. Light pressure is all that is required for sanding, polishing or
scrubbing. Excessive pressure will slow the tool and produce inferior results. Check your
work often, product is capable of removing material rapidly.
CAUTION: Under no circumstances should this product be used near water.
WARNING: Always unplug product from power supply before any of the following opera-
tions.
DETAIL SANDING
Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces
and tight spots or corners.
The pad tips may wear unevenly, depending on use. The pads are designed to allow you to
interchange and /or rotate the diamond tip.
FITTING SANDING SHEETS ( FIG. 2)
• Detach the two diamond-shaped tips from the sanding sheet.
• Hold the tool with the sanding base facing upwards.
• Place the sanding sheet onto the sanding base.
The diamond-shaped tip can be reversed and replaced when worn.
• When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto
the sanding base again.
• When the whole tip is worn, remove it from the sanding base and fit a new tip.
TIP OF THE SANDING BASE ( FIG. 3)
When the sanding base tip is worn, it can be reversed or replaced.
• Remove the screw.
• Reverse or replace the worn part.
• Fit and tighten the screw.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
should be performed by authorized service centers or other qualified service organizations, always
using identical replacement parts.
ACCESSORIES
Look for the following Sander accessories at your local retailer.
Catalog #
Description
Contents
74-583
120 Medium Sandpaper
5 sheets
74-584
180 Fine Sandpaper
5 sheets
74-585
220 Extra Fine Sandpaper 5 sheets
74-586
Sandpaper Assortment
1 sheet of 120 grit paper, 2 sheets each 180,
220 paper
74-588
1 OT Power Wool
3 sheets
74-589
4 OT Power Wool
3 sheets
74-581
Polishing Kit
2 sheets of 1 OT power wool, 2 sheets of 4 OT
power wool, 2 foam pads
74-582
Dry Scrubbing Kit
2 coarse abrasive pads, 2 fine abrasive pads,
2 foam pads
74-580
Sanding/Polishing Kit
2 sheets of 1 OT power wool, 2 sheets of
180 grit sandpaper, 2 sheets of 240 grit
sandpaper, 2 foam pads, 5 finger attachment
paper
Recommended accessories for use with your tool are available at extra cost. Listings per
retailer may vary. The hook and loop pad and individual bases are replaceable parts. If they
become worn, contact your local service center. For more information call: 1-800-544-6986
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
TROUBLESHOOTING
Problem
Possible Cause
• Unit will not start.
• Cord not plugged in.
• Circuit fuse is blown.
• Circuit breaker is tripped.
• Cord or switch is damaged.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Application / Accessory Matrix
ACCESSORY
RECOMMENDED APPLICATIONS / USES
M
P
, V
EDIUM GRIT SANDPAPER
AINT
ARNISH
F
S
INE GRIT SANDPAPER
URFACE BLENDING AND FINISHING
E
F
S
XTRA
INE GRIT SANDPAPER
ANDING BETWEEN COATS OF PAINT OR VARNISH
D
C
ETAIL SANDING TIPS
ORNERS
1 OT
/ S
P
POLISHING
TRIPPING WOOL
OLISHING METALS
4 OT
F
FINE POLISHING WOOL
INE POLISHING
A
GREY FOAM PAD
PPLYING AND REMOVING POLISH
-
L
WHITE NON
WOVEN PAD
IGHT SCRUBBING
-
H
RED NON
WOVEN PAD
EAVY SCRUBBING
The pads described above are available in kits where Sander products are sold. The hook
and loop pad and individual bases are replaceable parts. If they become worn, contact your
local service center. For more information call 1-800-54-HOW-TO (544-6986).
All manuals and user guides at all-guides.com
Possible Solution
• Plug tool into a working
outlet.
• Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Reset circuit breaker.
(If the product repeatedly
causes the circuit
breaker to trip,
discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Have cord or switch
replaced at Black
& Decker Service Center
or Authorized Servicer
, R
R
UST
EMOVAL
/ H
ARD TO REACH PLACES
/ S
TRIPPING VARNISH OR URETHANE
,
/
/
SATIN FINISH ON PAINT
VARNISH
URETHANE
-
DRY ONLY
/
-
RUST REMOVAL
DRY ONLY
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province. Should
you have any questions, contact the manager of your nearest Black & Decker Service
Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
P P
O O
N N
C C
E E
U U
S S
E E
P P
O O
P P
O O
N N
C C
E E
U U
S S
E E
P P
O O
D D
É É
T T
A A
I I
D D
É É
T T
A A
MODE D'EMPLOI
N° de catalogue 7434
M
'
M
'
ERCI
ERCI
D
D
A
A
VOIR
VOIR
CHOISI
CHOISI
V
.B
D
V
.B
D
ISITEZ
WWW
LACKAND
ISITEZ
WWW
LACKAND
POUR
ENREGISTRER
VOTRE
POUR
ENREGISTRER
VOTRE
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D'APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR
TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.
RENSEIGNEMENTS IMPORTANTS
• Ne jamais utiliser l'outil sans le papier abrasif recommandé bien installé sur le
socle muni.
• Le tampon les socles individuels peuvent être remplacés. Lorsqu'ils sont usés,
confier la réparation de l'outil au personnel d'un centre de service.
• Ne pas appuyer sur l'outil; laisser la ponceuse faire le travail.
•Il est déconseillé de poncer pendant de longues durées des murs secs avec l'outil.
MESURES DE SÉCURITÉ
AVERTISSEMENT : Lire et comprendre toutes les directives. Le non-respect de toutes
les directives suivantes présente des risques de secousses électriques,
d'incendie ou de blessures graves.
CONSERVER CES MESURES.
ZONE DE TRAVAIL
• S'assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et
des endroits sombres présentent des risques d'accidents.
• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme
celles dégagées par des liquides, des gaz ou des poussières inflammables). Les
étincelles générées par le moteur des outils électriques peuvent enflammer les poussières
ou les vapeurs.
• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu'on utilise
un outil électrique. Une distraction peut entraîner la perte de maîtrise de l'outil.
MESURES DE SÉCURITÉ RELATIVES À L'ÉLECTRICITÉ
• Les outils à double isolation comportent une fiche polarisée (une lame plus large que
l'autre). La fiche n'entre que d'une façon dans une prise polarisée. Lorsque la fiche
n'entre pas à fond dans la prise, essayer de nouveau après avoir inversé les broches
de la fiche. Si la fiche n'entre toujours pas dans la prise, communiquer avec un
électricien certifié afin de faire installer une prise polarisée. Ne modifier en aucune
façon la fiche. La double isolation
élimine le besoin d'un cordon trifilaire mis à la terre et
d'un système d'alimentation mis à la terre.
• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,
des cuisinières et des réfrigérateurs. Les risques de secousses électriques sont plus
élevés si le corps de l'utilisateur est mis à la terre.
• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration
d'eau dans l'outil augmente les risques de secousses électriques.
• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales
U U
R R
T T
R R
A A
V V
A A
U U
X X
U U
R R
T T
R R
A A
V V
A A
U U
X X
L L
L L
É É
S S
I I
L L
L L
É É
S S
B
& D
!
B
& D
!
LACK
LACK
ECKER
ECKER
.
/N
O
.
/N
O
ECKER
COM
EW
WNER
ECKER
COM
EW
WNER
.
.
NOUVEAU
PRODUIT
NOUVEAU
PRODUIT
Publicidad
