Declaration Of Conformity - STEINEL RS LED D2 S Guia De Informacion

Mounting procedure
• Switch OFF power supply ( Fig� 4�1 )
• Mark drill holes ( Fig� 5�1 )
• Drill holes and insert wall plugs ( Fig� 5�2 )
• Installation with concealed power supply lead ( Fig� 5�3 )
• Installation with surface-mounted power supply lead
( Fig� 5�4 )
• Connect conductors ( Fig� 5�5 )
• Make settings ➔ "6� Functions" ( Fig� 5�6 )
• Fit shade ( Fig� 5�7 )
• Switch ON power supply ( Fig� 5�7 )
6� Function
The sensor-switched light can be put into service after
mounting the enclosure and connecting to the mains power
supply. When putting the light into operation manually at the
light switch, the light will switch OFF after 10 seconds for the
calibration phase and is then activated for sensor mode. It is
not necessary to operate the light switch a second time.
Function - control dials ( Fig� 6�1 )
Factory settings:
Time setting: 5 seconds
Reach setting: 8 m
Twilight level: 2000 lux
Basic brightness: 10%
Time setting ( stay-ON time ) ( Fig� 6�1/F )
The light's ON time can be set to any period from approx.
5 seconds to a maximum of 15 minutes. Any movement
detected before this time elapses will restart the timer.
Note:
After the light switches OFF, it takes approx. 1 second
before it is able to start detecting movement again. The
light will only switch ON in response to movement once this
period has elapsed.
The shortest time setting is recommended when adjusting
the detection zone and performing the functional test.
Reach setting ( sensitivity ) ( Fig� 6�1/G )
Reach is the term used to describe the diameter of the
more or less circular detection zone produced on the floor
after mounting the sensor-switched light at a height of
2.50 m.
– Control dial set to maximum = max. reach ( 8 m )
– Control dial set to minimum = min. reach ( 2.50 m )
Twilight setting / response threshold ( Fig� 6�1/H )
The light's chosen response threshold can be infinitely
varied from approximately 2 to 2000 lux.
– Control dial set to = daylight mode ( depending on
ambient brightness )
– Control dial set to = twilight mode ( approx. 2 lux )
The control dial must be turned to
the detection zone and performing the functional test in
daylight.
Night light ( Fig� 6�1/E )
The night light provides illumination at approx. 10% of full
light output. The light only switches to maximum output
( 100% ) in response to movement in the detection zone
( see Time setting ). The light then switches to the activated
night light level.
– Control dial set to
– Control dial set to 0 = night light deactivated
Night light is ON when the level of light falls below the
brightness threshold. Night light is always ON when daylight
mode is activated.
Manual override function
If a mains switch is installed in the mains supply lead,
the following functions are available in addition to simply
switching light ON and OFF:
Manual override ( Fig� 6�2 )
1 ) Activate manual override:
Switch OFF and ON twice. Light is set to
manual override for 4 hours. Then it returns automatically to
sensor mode.
2 ) Deactivate manual override:
Switch OFF and ON once. Light goes out or switches to
sensor mode.
Important:
The switch should be actuated in rapid succession ( in the
0.2 to 1 second range ).
Electrical and electronic equipment, accessories and pack-
aging must be recycled in an environmentally compatible
manner.
EU countries only
Under the current European Directive on Waste Electrical
and Electronic Equipment and its implementation in national
law, electrical and electronic equipment no longer suitable
for use must be collected separately and recycled in an
environmentally compatible manner.
Important note: the control gear cannot be replaced.
when adjusting
Hereby, STEINEL Vertrieb GmbH declares that the radio
equipment type RS LED D2 S is in compliance
with Directive 2014/53/EU. The full text of the EU decla-
ration of conformity is available at the following internet
address: www.steinel.de
- 11 -
= night light activated
7� Disposal
Do not dispose of electrical and electronic
equipment as domestic waste.
8� Declaration of Conformity