Usage Of The Machine - Garland ULTIMATE 519 LE Manual De Instrucciones

5.3. VERIFICATION POINTS PRIOR TO USE
The current supply and its related tension must be
those stipulated on the characteristics label.
Check the machine and look for lose pieces (screws,
nuts, covers etc) and for any damages. Tighten, repair
or replace the pieces that you have noticed not to be
in a perfect working order. Do not use the machine if it
has lose or damaged pieces.
5.3.1. VERIFICATION OF THE ELECTRICAL
CONNECTION
Check that the connection to the mains is correct and
that the electric current is adequate for the machine.
Any attachments must comply with to the needs of
this machine.
Check that the cable is behind the machine and never
in the working area.
5.3.2. VERIFICATION OF WATER CONNECTION
Open the water intake and check that there are no
leakages. If there are any leakages, replace or repair
the hoses or its connectors.
5.3.3. PLACEMENT OF THE MACHINE
Ensure the machine is in a vertical and stable position.
5.4. START UP AND STOPPAGE
The gun has a closing security device
that if in place will not allow the gun to
function.
Before starting the machine, the machine
must have its internal circuit full of water.
To fill, push the trigger of the gun with
the machine stopped (switch in the ¨o¨ position) until
water with no pressure drips from the lance. If the
pump works with the internal circuit not full of water
(working in dry conditions), the pump will be damaged.
Start up:
Place the switch in position ¨1¨.
On/Off switch
Remove the blocking security
device of the gun and action
the trigger.
Stoppage:
Security device of
Place the switch
the gun
in the ¨O¨ position.
The engine of the
machine will stop.
The TSS system allows the engine to stop when the
trigger is not pressed. For a proper usage, once the
trigger is not pressed, we should wait 4 or 5 seconds
before pressing the trigger again.
29/104
English English
If the machine has not been used for a
couple of minutes you must place the On/
Off switch to the Off position ¨O¨.
NOTE: When pressing the trigger, the power of the
water forwards will have a back pull on the user.
Always hold the lance with two hands and tightly and
always be in a stable position to avoid falling over or
watering unwanted areas.
5.5. VERIFICATION AFTER USE
Check that when the trigger is not pressed, water
does not flow out under pressure through the lance,
hose or any connectors.
If you detect any of these leakages please tighten or
repair these parts.

6. USAGE OF THE MACHINE

Use this machine only for its proposed work. The
use of this machine for other jobs not stipulated in
this manual is dangerous and could cause injuries/
damages to the user and to the machine.
Do not use this machine if tired, ill, if under the
influence of medicines, alcohol or drugs.
Pay particular attention when using this machine as
the floor will be wet and there is an obvious danger of
slipping.
Do not use the machine if dark or with reduced
visibility as the work area will not be fully visible.
Lack of sleep or fatigue can cause damages and
accidents.
Limit your work time to ten minute periods with a rest
break between a further ten to twenty minutes.
Never leave he machine unattended.
Do not allow anybody into the work area. The work
perimeter should never be less than 15 meters.
Anything less is considered dangerous.
Hold the handle of the machine firmly to reduce the
risk of lack of control over the machine.
Only use original accessories and spare parts or
those recommended by the manufacturer. Otherwise,
damages and/or injuries to machine and user could
happen.
Whilst working, hold the gun with both hands.
If a work pause superior to 2 minutes is done, stop the
engine by placing the switch in the ¨o¨ position.
NOTE: This machine has a thermal sensor that
protects the engine in case of an overload. If the
thermal sensor is activated, the machine will stop and
will only start again after a few minutes.
Cleaning:
To clean, hold the gun with both hands and direct the
high pressure water to the objects to be cleaned. Do
not get too close to the objects as you could damage
these. We recommend maintaining always a minimum
distance of 30cm. From the objects being cleaned.
There are two lances, a standard lance and a rotating
lance. Use the rotating lance for those jobs where a
high pressure is needed. Use the standard lance for
those jobs that where you want to move dirt from one
place to another or where a moderate cleanliness is
needed.
30/104