Safety Precautions - Campingaz 360 Grill Instrucciones De Empleo

D - CONNECTING THE GAS CYLINDER
Use a regulator compliant with EN 12864 or EN16129.
Campingaz's regulator is recommended (see section C).
An adjustment valve must be present on the gas cylinder
or on regulator.
When replacing an empty cylinder, read Section F:
"Removing or changing the gas cylinder".
When installing or removing a gas cylinder, always
operate in an open, very well-ventilated place, never in
the presence of a flame, spark or any other source of heat
(cigarette, electrical appliance, etc.), and away from other
persons or inflammable materials.
1. Place the gas cylinder on the ground, behind or next
to the appliance. Keep it far away from parts that can
become hot.
2. Close the valve on the regulator or gas cylinder.
(Fig. 3A)
3. Close the control knob on the appliance by turning it
towards "O". (Fig. 3B)
4. Screw or push the regulator onto the cylinder or onto
the valve on the gas cylinder.
5. Connect the flexible hose to the appliance and the
regulator. Secure the connections thanks to the clamps
provided with the hose (Fig. 3C)
6. Check that the air holes in the burner tube, close to the
injector, are not obstructed by dust or cobwebs.
CHECKING FOR GAS LEAKS (Fig. 4)
Do not check for leaks using a flame. Use a gas leak
detecting liquid.
1. Close the valve on the regulator or gas cylinder. (Fig.
3A)
2. Apply gas leak detecting liquid to the cylinder /regulator
/ hose / appliance joints. The control knob should
remain closed: off position (O). (Fig. 4)
3. Open the gas supply (valve on the regulator or
cylinder). (Fig. 3D)
4. Any gas leaks will be indicated by bubbles.
5. Shut off the gas supply (valve on the regulator or
cylinder).
6. The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
appliance must not be used until the leak is stopped.
Important:
An overall inspection and leaks check must be carried
out at least annually and always after changing the gas
cylinder.
E - OPERATION

SAFETY PRECAUTIONS

Do not use your appliance at a distance closer than
20 cm to a wall or flammable object, nor closer than 1
metre to a ceiling.
Before lighting the appliance in Grill or Plancha setting,
make sure to fill the reservoir with water to "MAXI" level.
Protect your appliance from wind, its performances will
be increased.
WARNING: Accessible parts may be very hot. Keep
young children away.
Never touch the burner during or just after using the
equipment.
Position the appliance on a stable, horizontal surface
and do not move when in use.
Do not use a cooking vessel smaller than 12 cm or larger
than 26 cm in diameter.
Never leave the cooking plate on fire without foodstuffs
longer than one minute (except for the initial pre-heating
period) otherwise the special coating will be damaged.
To avoid damaging the non-stick coating, always use
cooking utensils in silicone or wood to manipulate your
dishes.
In the event of a leak (smell of gas), close all valves.
Wait for the appliance to cool down completely before
handling it for storage.
After use, always close the valve on the regulator or gas
cylinder.
It is recommended protective gloves to be worn to
handle components which may be very hot.
Important : check the presence of flame through the
window located on the firebox over the control knob (9)
(Fig. 1A). In case the burner extinguishes whilst grilling,
close the gas valve immediately and wait 5 minutes to
let the gas be evaporated. Re-ignite the appliance after
this waiting time.
A - Plastic lid :
The plastic lid is fastened on the top of the firebox thanks to
clips (Fig. 5). He keeps all the inside parts in place during
the transport. Remove it before use.
B - Use of the water tank :
Place the appliance on a flat ground. Fill the tank with
water till the MAX setting. (Fig. 6A) Pay attention not to
spill water on the burner.
After the cooking session, you may disconnect the water
tank to throw the mixture of water and grease and clean
it. You can use a sponge impregnated with non-abrasive
detergent product or put the tank in the dishwasher.
Disconnect the water tank by pulling the lock button (8).
Keeping the button pulled till its stop setting, remove the
tank by moving it upwards. (Fig. 6B)
After the cleaning, put the tank back on the base:
1- Pull the lock button (8) (Fig. 6C)
2- Align the flame viewing window (9) with the control knob
(7). The notches (10) of the base of the tank must be
aligned with the locking axle (11) (Fig. 6D)
3- Place the tank on its support
4- Release the button, the tank is locked (Fig. 6E)
Fill in the tank with water till the MAX setting if you want to
use it again. (Fig. 6A)
19
GB