Installation; Venting Methods - Yale PWLCL630SS Guía De Instalación, Uso Y Mantenimiento

Ocultar thumbs Ver también para PWLCL630SS:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Installation

• It is recommended that the vent system be installed before
hood is installed.
• If you are installing the optional backsplash with shelves for
heat lamps, follow the instructions included with that product.
• If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to rear
wall.
• Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
• Check that all installation parts have been removed from the
shipping carton.
1 Disconnect power.
2 Determine which venting method to use: roof or wall exhaust.
NOTE: This hood is factory set to vent through the top air exit.
If you decide to use the rear vent exit, you have to remove the
rear vent cover and relocate it to the top vent exit.
3 Select a flat surface for assembling the range hood. Place
covering over that surface.

Venting Methods

Outside Top exhaust
Vertical duct Ø 10" (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the cabinet's bottom or roof for ductwork, electrical
wiring and keyhole screw slots.
C
" (19 mm)
3
D
4
E
FRONT OF THE HOOD
PWLCL630SS
A
30" (760 mm)
B
C
D
E
9
F
3
" (90 mm)
16
G
H
8
CL
5
"
5
"
1
1
4
4
(133mm)
(133mm)
Ø 1"
(25.4 mm)
A
PWLCL136SS
PWLCL148SS
36" (912 mm)
48" (1217 mm)
12" (305 mm)
1" (25.4 mm)
5
2
" (65 mm)
8
1
7
" (190 mm)
2
7
6
" (164 mm)
16
2" (50 mm)
1
3
" (89 mm)
2
Outside rear exhaust
Horizontal duct Ø 10" (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the wall for ductwork, electrical wiring and keyhole
screw slots.
F
J
G
H
I
PWLCL630SS
A
30" (760 mm)
B
C
D
7
E
3
" (87 mm)
16
F
G
H
WALL
I
J
F
B
1 Remove the grease filters.
G
2 Remove the blower mounting screws. Put the screws in a
H
safe place in order to use them again.
3 Set free the two blower springs from the top of the range
hood housing.
CL
E
D
C
C
D
Ø 1"
(25.4 mm)
5
"
5
"
1
1
4
4
(133mm)
(133mm)
B
B
A
PWLCL136SS
36" (912 mm)
7
9
" (250 mm)
8
4" (100 mm)
9
7
" (192.6 mm)
16
5" (127 mm)
15
2
" (75 mm)
16
1
7
" (192 mm)
2
2" (50 mm)
2
6
"(157 mm)
8
11
3
"(94 mm)
16
TOP OF
E
THE HOOD
PWLCL148SS
48" (1217 mm)
9
6
" (167 mm)
16
7
5
" (149 mm)
8

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pwlcl136ssPwlcl148ss

Tabla de contenido