Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
OUTSIDE TOP EXHAUST
A
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3.
Adapting Microwave Blower for
Outside Top Exhaust
A4. Check Damper Operation
A5.
Mount Microwave Oven
A6.
Adjust Exhaust Adaptor
A7. Connect Ductwork
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A1.
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
1
2
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
each bolt.
Installation Instructions
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
N INSTRUCTIO NS
IN THE INSTALLATIO
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
4"
This Rear Wall Template
mounting plate and to locate
the horizontal exhaust
outlet.
1. Use a level to check
that the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
screw mounted firmly in
a stud to support the weight
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
Darle vuelta a la hoja
para consultar la
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
THE CENTERLINE .
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
" (19 mm) onto
3
⁄
4
EN-12
(Vertical Duct)
along the dotted line.
Trim the rear wall template
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
THE CENTERLINE .
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
To use toggle bolts:
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
Place the mounting plate against the wall and
3
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the Rear wall template when
pushed flush against the wall and that the plate is
properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts.
Bolt End
Publicidad
Tabla de contenido
