Milwaukee CARRY-ON 2845-20 Manual Del Operador página 6

GROUNDING
Improperly connecting the ground-
WARNING
ing wire can result in the risk of
electric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Only if permitted and required by local codes,
the bonding terminal stud may be wired using
14 AWG Copper insulated solid or stranded wire
or wire sized per local codes.
Grounded Tools (Three-Prong Plugs)
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
"live" terminal.
Your tool must be plugged into an appro-
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
Bonding the Power Supply
The power supply bond terminal is connected to the
ground terminals of each receptacle.
Before using the bond terminal, consult a qualified
electrician, electrical inspector, or local agency hav-
ing jurisdiction for local codes or ordinances that
apply to the intended use of the power supply.
The power supply is isolated from the frame and from
the AC receptacle ground pin.
Electrical devices that require a grounded receptacle
pin connection will not function if the receptacle
ground pin is not functional.
Only if permitted and required by local codes, the
bonding terminal stud may be wired using 14 AWG
copper insulated solid or stranded wire or sized per
local codes.
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Batteries
To remove the batteries, push in the release but-
tons and pull the battery packs away from the power
source.
To insert the batteries, slide the pack into the body
of the power source. Make sure they latch securely
into place.
NOTE: The unit requires four charged battery packs
to operate.
Inserting/Removing Extension Cord
The power source must be plugged in to charge the
batteries. The power source will charge up to 4 bat-
teries that are installed in the charging bays. Plug
a suitable extension cord into the power source.
The power source must be plugged in to a 120V
receptacle to charge batteries. To disconnect the
extension cord once charging is complete, remove
the cord from the power source.
The power supply either discharges or charges the
battery packs one function at a time. Once battery
packs are charged, unplug the extension cord and
plug in tools or products.
Locking/Unlocking the Battery Packs
1. Twist the handle collar to unlock the handle prior
to pulling apart the battery lock bars attached to
the carrying handle.
Fig. A
2. Twist the handle collar to the lock position.
There is a hole in the bar to attach a padlock (not
included).
3. Attach the padlock. Doing so prevents the batter-
ies from being removed from the power source.
NOTE: It is recommended that the battery lock bars
be positioned closest together with the handle collar
in the lock position when not over battery packs.
To install the carrying strap, attach the hooks from
the strap on both carrying strap loops. Make sure the
hooks are secure on the loops prior to carrying the
power source. To remove, reverse the procedure.
Tethers can be attached to the power source any-
where on the roll cage.
6
ASSEMBLY
Recharge only with the charger
specified for the battery. For spe-
Installing the Carrying Strap
Tethering the Power Supply