Sleep Mode; Audio Menu (Optional) - HotSpring HOT SPOT Serie Manual Del Propietário

3. To shut the Summer Mode off, press the MODE ( or ) button
until TOOLS is displayed. Then press the (+) button to enter
the TOOLS submenus. Press the MODE ( or ) button in
the TOOLS submenu until SUMMR is displayed on the screen.
Press the (-) button to deactivate.

SLEEP MODE

The Sleep Mode operation is a feature that minimizes pump operation
during quiet evening hours. For example, if Filter Cycle 1 (F1) is set to
activate at 8:00 a.m., by default, Filter Cycle 2 (F2) will activate at 8:00
p.m. (12 hours later). During 8:00 p.m. to 8:00 a.m., if the spa should call
for heat, the pump and heater will activate to heat the spa under normal
temperature demand. However, when in Sleep Mode, should the spa
call for heat, the pump and heater will be suspended after Filter Cycle
2 (F2) until the activation of Filter Cycle 1 (F1), at 8:00 a.m. to minimize
pump activation during quiet evening hours.
Important: Power-up of the spa starts the F1 sequence. In order for the
sleep mode to work in the evening hours, the spa must be powered up
in the early morning hours. The Sleep Mode will always be active the
6-12 hours between the end of (F2) and the beginning of (F1) depending
on how the filter cycle program is set.
Note: If temperature drops below 80º F (27º C), heater will automatically
activate to prevent spa from freezing.
To activate Sleep Mode feature:
A. Press the MODE ( or ) button until
the TOOLS screen is displayed.
B. Press the (+) button to enter the TOOLS submenus.
C. Press the MODE ( or ) button until ECON is displayed.
D. Press the (+)button to activate Sleep Mode. Moon & Stars icon will
appear on the screen of the control panel, indicating this feature
has been activated.
To deactivate this feature, simply repeat steps A-C then press the (-)
button.
FILTER CYCLES
When the spa is first powered up, the automatic filter cycle will wait
10 minutes before starting. Your spa will automatically turn the first
filter cycle on for 60 minutes on low speed. The second filter cycle will
activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will
be displayed in the control panel during the filter cycle.
NOTE: When using @ease SmartChlor, the initial recommended
minimum filter cycle setting is 2 hours 30 minutes, twice a day (5 hours
total). You may adjust this setting based on your bather load.
NOTE: The optional FRESHWATER III ozone system only works during
the filter cycle.
To modify the length of either filter cycle:
A. Press the MODE ( or ) button until the
TOOLS menu is displayed.
B. Press the (+)button to enter the TOOLS
submenus.
C. Press the MODE ( or ) button until FILT1 or FILT2 is displayed.
D. Press the (+)button to enter FILT1 or
FILT2. F1 or F2 icon will flash.
E. Using the (+) or the (-) button, adjust the
desired filter cycle time, from 0 to 6
hours.
Operating Instructions
English Spanish
F. Press the MODE ( ) button in FILT1 to go
to the RESET screen. Press the (+) button
if you want to reset the filter 1 starting time
to the current time or press the MODE ( )
button to go the the EXIT screen. Press the
(+) button in the EXIT screen to go to the FILT2 screen.
The filter cycle will activate the jet pump on low speed for the entire
cycle. When activated, the filter cycle icon on the display is turned on.
If the temperature exceeds the set point by three degrees F for more
than three hours, the system will cancel the filter cycle for the remaining
filter cycle time. Should the temperature cool down to 1.5 degrees F
(1 degree C) below the set point before the end of the cycle, the cycle
will resume for the rest of the time. Should you use the spa during the
filter cycle by placing the jet pump on high speed, the Filter icon and
Jets icon will be on. Once the jet pump has been shut off, a ten minute
tranquil mode begins (Filter & Jet icons are off during tranquil mode
while F1 or F2 remain lit). The Filter and Jet icons will come back on
once the tranquil mode ends if the filter cycle timer is still on.
BRIGHTNESS - LCD
If you would like to change the brightness of the
Control Panel screen:
A. Press the MODE ( or ) button until the
TOOLS menu is displayed.
Press the (+)button to enter the TOOLS submenus.
B.
C. Press the MODE ( or ) button until LCD is displayed.
D. Press the (+)button to enter into the LCD menu.
Using the (+) or the (-) button, adjust the desired screen brightness.
E.

AUDIO MENU (OPTIONAL)

The following applies to spas that have an optional wireless audio
system installed:
When the wireless audio system has been installed on the spa, the
control panel can be used to control the audio system. The following
information demonstrates how to navigate the music menu by using the
spa's control panel.
AUDIO MENU
An AUDIO menu will be accessible on the
control panel screen.
To access the menu, press the MODE ( or
) button until AUDIO is displayed.
BASIC CONTROL PANEL OPERATION
1. To enter into a sub-menu press the (+)button.
2. To move to the next menu press the MODE ( ) button
3. To exit from any sub-menu, press MODE ( or ) button as many
times as necessary until EXIT is displayed then press the (+)button
to exit that sub-menu.
TO TURN AUDIO SYSTEM ON/OFF
(OPTIONAL)
From the AUDIO screen:
Press the (+)button to display POWR -.
1.
Page 16
French
POWER POWER
POWER POWER
POWER POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
Operating Instructions
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER