Water Softener; Detergent Use - cecotec BOLERO AGUAZERO 8000 FULL BUILT-IN Manual De Instrucciones

ENGLISH

4.2 Water softener

- This dishwasher is equipped with a water softener which uses a salt compartment
specifically designed to reduce water hardness.
- To find out the hardness level of your tap, you can contact your water company or use a
test strip.
- You must set the water softener manually according to the water hardness in your area,
to do so use the water hardness dial. The goal is to optimise and customise the salt
consumption level.
Water hardness table
Water hardness
Germany France United mmol/l
ºdH ºfH Kingdom
ºClarke
0 - 5 0 - 9 0 - 6 0 - 0.94
6 - 11 10 - 20 7 - 14 1.0 - 2.0
12 - 17 21 - 30 15 - 21 2.1 - 3.0
18 - 22 31 - 40 22 - 28 3.1 - 4.0
23 - 34 41 - 60 29 - 42 4.1 - 6.0
35 - 55 61 - 98 43 - 69 6.1 - 9.8
1 ºdH = 1.25
ºClarke = 1.78
ºfH = 0.178 mmol/l
Factory setting: H3
- Every cycle with a regeneration operation uses 2.0 additional water litres and 0.02 kWh
more and the programme takes up 4 more minutes.
Setting the salt consumption
Follow these steps to set the salt consumption.
1. Close the door and turn on the device.
2. In the next 60 seconds, hold down the '>' icon more than 5 seconds to enter the water
softener setting mode.
3. Press the '>' icon again to select the proper setting according to your local area, the setting
will change following this sequence: H3->H4->H5->H6->H1->H2.
78
Water Regeneration Salt
softener is produced consumption
level every X (grams/cycle)
programmes
in a sequence)
H1 No 0
regeneration
H2 10 9
H3 5 12
H4 3 20
H5 2 30
H6 1 60
4. Do not press any icon for more than 5 seconds or press the power button to complete the
setting and exit this mode.

4.3 Detergent use

Use only detergents designed specifically for household dishwashers. Keep the detergent
-
in a cool, dry place and out of reach from children.
The ingredients used in the detergents are necessary to remove dirt from the dishwasher.
-
Do not fill the compartment with powder detergent until it is ready to wash the dishes.
-
The necessary detergent amount will depend on the cycle, the load size and the dishes dirt
-
level. Add an adequate amount to ensure optimum performance.
If the detergent amount is too high, you will notice glass and dishes have whitish stripes or
-
bluish layers, which may cause corrosion. Continued use of too much detergent may cause
damage to the dishwasher.
If the amount of detergent is too low, it can cause bad cleaning, as well as whitish stripes
-
if the water is hard.
Check the manufacturer instructions for the detergent to get more information.
-
Filling the detergent (Fig. 13 - 13A)
-
1. Slide the detergent compartment release tab to the right to open the cover.
2. Add detergent in the biggest hole (A) for the main wash. For dirtier loads, also add detergent
in the smaller hole (B) so that detergent is released during prewash.
3. Close the cover and press it until it is blocked in place.
Note
Remember that, depending on water hardness, the setting can be different.
-
Respect the manufacturer recommendations in the detergent package.
-
4.4 Rinse aid use
Use only detergents designed specifically for household dishwashers. Keep the rinse aid in
-
a cool, dry place and out of reach from children.
Rinse aid is used to promote the drying of the dishes without marks and stains. The rinse
-
aid is automatically released during the last rinse to prevent water droplets from forming
on the dishes, which can leave stains and marks.
This dishwasher is designed to use liquid rinse aids.
-
If the rinse aid dose is too low, there will be whitish stains in the dishes and they will not
-
dry correctly.
If the rinse aid dose is too high, you will see bluish layers on glass and dishes.
-
Never fill the rinse aid compartment with other substances, as this could damage the
dishwasher.
Filling the rinse aid compartment
Follow the steps below:
ENGLISH
79
AGUAZERO 8000 FULL BUILT-IN